Models > CSF22EBC > Instructions

CSF22EBC Hotpoint Refrigerator - Instructions

All installation instructions for CSF22EBC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSF22EBC
31-45 of 206
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

hinge set

  • Customer: Bernice from Chesterfield MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 3 of 3 people found this instruction helpful
Was not hard. It was the bottom hinge so we had to take the door off, but that was only a matter of a couple of screws. Replaced the bottom hinge and closing cam, replaced the door and it was done.

Door was squeaky and would no close

  • Customer: Ronald from Yuma AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and applied a little lubricant to the cam and job complete.

excessive door swing

  • Customer: PETER from ENGLEWOOD NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 3 of 4 people found this instruction helpful
Removed the top hinge and the door.
Removed door stop held in place by 2 screws, installed new door stop.
re-installed door and top hinge.
Easy once the correct diagnosis was made
It would have been nice if I could have e-mailed you the symptoms and received an accurate diagnosis. As it developed, I initially replaced the door cam before realizing that the door stop itself had broken.

Freezer not cold

  • Customer: Henry from Wichita Falls TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
I had to defrost freezer first becasue it was heavily iced up. Then I found that one of the heater elements was "open". I removed both of the old heater elements and installed the replacement parts.

Not cooling - cond fan did not turn

  • Customer: Daniel from Great Falls VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
Unplug refrig! Removed back cardboard covering (~5 screws)
(1) Cleaned all the dust out (hardest part!)
(2) Removed power wire to motor
(3) Removed 3 bolts holding motor to frame
(4) Removed motor/fan blade to the left
(5) Moveded fan blade to new motor (clean it!)
(6) Replaced motor, reinstalled 3 bolts
(7) Plugged power wire to new motor
(8) Tested it - worked fine, failed safe, drained to bilge!
Replaced back cover (had to tape it since I horked it up removing it)

Started to see a little sweat in freezer and ice cream not getting hard frig staying on longer.

  • Customer: Frank from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench set
  • 3 of 4 people found this instruction helpful
Pulled frig out. Removed back cover. Unplugged frig, unplugged motor. Removed fan from old motor first then 3 screws from bracket that holds motor and removed motor. Reattached motor back on bracket, reattached fan on motor. Plugged fan back in and then frig. Everything worked fine no more soupy ice cream !!

FAN STOPS - BAD BEARING

  • Customer: JACK R from LEESBURG FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
UNPLUG UNIT FROM WALL. REMOVED COVER FROM REAR OF UNIT. CLEANED COILS WITH VACCUUM CLEANER. UNPLUG WIRES FROM FAN MOTOR AND REMOVE NUT HOLDING FAN BLADE TO MOTOR. REMOVE 3 SCREWS HOLDING MOTOR TO MOUNT. REPLACE WITH NEW MOTOR,MAKE SURE FAN BLADE DOES NOT HIT HOUSING. PLUG UNIT BACK IN WALL AND REPLACE COVER.

Existing light switch was hard to remove.

  • Customer: Stephen from Jupiter FL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

DOOR NOT CLOSING TIGHTLY + STAYING OPEN

  • Customer: Jeff from Venice FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
TURNED OFF WATER TO REF , REMOVED BOTTOM KICK PLATE , GOT A TOWEL AND DISCONNECTED THE WATER LINE PLASTIC FITTING AND UN SCREWED THE (2) TUBE CLAMPS UN SCREWED THE COUPLING AND ((CAREFULLY )) SLID OUT THE TUBE FROM THE COMPRESSION FERRELS ! ( BE CAREFUL AND DO NOT BREAK OR DISTORT THEM + REMEMBER EXACTLY THE ORDER THEY ARE REMOVED !
SLID THE PROTECTOR SPRING SHROUD FROM THE PLASTIC TUBE , TOOK OGG THE TOP HINGE COVER THEN REMOVER THE TOP HINGE . CAREFULLY LIFTED THE DOOR OFF FEERING THE PLASTIC TUBE THROUGH THE BOTTOM HINGE WITH MY FOOT ! GOT THE DOOR OFF REMOVED THE BOTTOM HINGE + PUT THE NEW ON ON, THEN REMOVED THE DOOR CAM WHICH WAS BROKEN ON THE BOTTOM OF THE DOOR , LIFTED THE DOOR UP AND CAREFULLY FED THE WATER LINE THROUGH THE NEW BOTTOM HINGE . ATTACHED THE TOP HINGE AND REASSEMBLED THE REST SAME AS I HAD DISSAMBLED IT . TURNED ON WATER ( CHECKED FOR LEAKS ) ! ALL WORKING 100% A-OK ! THIS COMPANY IS THE BEST ! ORDERED THE PART AT 1 PM AND HAD THE PART AT 2 PM THE FOLLOWING DAY MANY THANKS : )

unusually noisy

  • Customer: Anthony from South Plainfield NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 3 of 4 people found this instruction helpful
Removed the three screws from old motor body-bracket assembly , pulled off 1/4'' spade terminals and removed shield from terminal block for re-use.
Removed fan from old unit and installed on new,
screwed new motor in place, replaced terminal wires, plugged back in refrigerator.
Now my old rerfrigerator is whisper quiet

Slide rail was missing when we bought house

  • Customer: Joe from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Got the part in and needed two screws to installed on left side. Service was great on the part as it was delivered in 3 days from the time we ordered. Thanks for the quick service

switchlight on my refrigerator was not working

  • Customer: Eileen from Coto de Caza CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 4 of 8 people found this instruction helpful
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

worn/broken cam , door doesn 't self close

  • Customer: Charles from Franklinville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .

Door stop weakened and cracked

  • Customer: James from Annapolis MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
Two nuts, door was off. 2 nuts stop was off. Nuts on, door on, nuts on.

Could not have been more easy.

Broken slide rail for Veggie drawer

  • Customer: Tony from Chesterfield MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Emptied the drawer and removed it. Then took off the old slide rail. Then I got some hot soapy water and cleaned the walls of the refridge while I was down there and had everything out. I then installed the slide rail put the drawers back in loaded the fridge and sat back and said I just saved myself about $200.00. You guys are awesome we got the part 2 days after we ordered it Thank you for the great service.

Tony The Birdman
All Instructions for the CSF22EBC
31-45 of 206