CSD2525ARW Amana Refrigerator - Instructions

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

First Remove ice holder, now take out nut left side under tray, remove tray from mounts, unplug wires, remove tray from freezer, remove solenoid assy from tray try to keep it from coming apart, remove motor from tray, the auger yoke is on a shaft that has to be removed by turning it clockwise (reverse threads). i used a small Chanel lock to hold shaft when removing yoke, Now remount the motor and yoke, remount the spring loaded solenoid assy, slide the ice bin enclosure back in a ways, then reconnect the wiring harness, remount it rest of the way in, install the nut. and your good to go.

i was having to completely empty the freezer about every 4 days and take the back cover off and use a blow dryer (with appliance the powered off) to remove the ice buildup. once the ice is gone, the heater coil is easily removed with a small wire clip. i measured the coil with my voltmeter and it was 220k or so, no open as i expected. the new part gave me a different reading but only about 10k difference. i decided to install the part and see. well, it's been 2 weeks now and the fridge is ice cold and working great again! saved a bundle by doing it myself and the stress of losing food in the fridge - thanks parts select!

We purchased 3 parts, in order of probable part that was broken. Website indicates that the Ice Maker Assembly was 75% likely the problem and indeed it was. Didn't need to install the other 2 parts. It wasn't too difficult to replace. Thanks for the advise, it was right on!

Changed bulb, not the problem, had to remove switch to identify correct choice to order (3 pronged verus 2) after that it was easy beyond having to stand on my head to make the exchange. (N B before removing old switch it actually came back to life)

I'm a 65 year old widow on a limited SS income, so I needed to get my refrigerator fixed as cheaply as possible. Partselect's troubleshooting guides took me right to the problem. I ordered the part on a Friday and it arrived the next Tuesday. It probably took me a little longer than it would a repairman, but I did it myself with just a screwdriver and a nut driver and it only cost me $45 instead of the $200 plus it costs my daughter to have someone else replace hers two years ago. Always remember to unplug amy electrical device before removing the covers or attempting any repair. All I had to do was remove the lower back cover on the refrigerator and, using the partselect diagram, locate the casing that covered the start relay and the overload switch on the left side of the compressor. I popped the casing off with the screwdriver, pulled the relay off (it's sits on two prongs), and remove the red terminal wire from the relay. Installation of the new relay is the reverse steps of the removal. Thanks, Partselect! I will be doing business with you again if the need ever arises.

Watched the video on the web site and then followed the instructions. It was very easy to change. After changing it, I filled it with water from a cup to get it started making ice since the video does not address how to do this. It has been working well ever since. If you are handy with tools, you can do this.

I put in a new ice maker because it was not in very good condition. The water valve had a very slow leak which allowed water to freeze on the way to the ice maker and plugged the line. This problem was in one of your repair articles all of which were very welcome

I had to replace the whole unit. The tray should have lasted longer and there should have been a replacement tray available.The installation was easy. 3 screws removed, unplug unit, turn off water and put in new unit.