Models > CSC24GRSBWH > Instructions

CSC24GRSBWH Hotpoint Refrigerator - Instructions

All installation instructions for CSC24GRSBWH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSC24GRSBWH
886-900 of 924
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The drive cup was old,worn,slipping and appeared to have never reached deep enough.

  • Customer: Frank from Villa Rica GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the front of the unit assembly and removed the entire auger unit and drive assembly. I married the old drive cup and new drive cup back to back using vise grip pliers, drilled 4 3mm holes, installed 4 phillips head stainless steel screws and, using an emory wheel, ground off the exposed screw ends. I then re-installed the drive assembly and auger unit. This increased the length of the drive cup allowing the drive to fit without any slippage. The entire cost was less than $18.00 including shipping and screws and took about 1 hour. It works great.

Put the part in and observed water leaking from the ice maker which caused the cup to break

  • Customer: John from Ravenden AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered new Ice Maker from you and fixed the problem completely.

The girlfriend opened the door and then it wouldn't shut on its own or stay closed

  • Customer: Gregory from Ontario CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Empty door first then take a phillip heads screw driver and unscrewed the top hinge cover 1 screw. Then used 5/16 nut driver to loosen top hinge from fridge. remove door by lifting and then lay on table to replace the lower washer that is held in by 2 screws and you only need to loosen one all the way leaving one in to align then replace and tighten it up your done.

Door would not close properly at the last few inches, now it closes good at this time but now need to be raised up to the 5/8 inch as the book says, haven't done that yet

  • Customer: Carol J from Alexandria KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the door closing cam works fine.

Freezer door would not close properly

  • Customer: Lynne from Toledo OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Using the #2 Phillips screwdriver I removed the top hinge cover from the top of the freezer door. Next I used the 5/16 nut driver to remove the 2 bolts holding the top hinge in place. Once it was removed I was able to lift the door off the bottom hinge. Placing the door on a flat work surface I loosened the bottom bolt holding the cam in place. I next removed the bolt holding the hinge in place. I was then able to remove the broken cam and replace it with the new one. I then replaced the bottom bolt making sure the hole for the cam and the hole for the hinge are lined up. I then tightened the bottom hinge bolts. I carefully placed the door back on the bottom hinge and put the top hinge back on.

Refrigerator door didn't close without a big push.

  • Customer: Susan from Chevy Chase MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took door off. Replaced two cams at bottom of door, referencing those on the bottom of the freezer door. Also followed a video on the net. Worked like a jewel!

Door didn't shut cleaning, by itself

  • Customer: Jim from Wheaton IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video online, and said, "hey, I can do that." And yep, I did. I'm pretty comfortable with handyman work - but had never tackled a frig door before. The door closing cam that had completely come apart turned out to be straight forward to fix with the replacement part.

Refrigerator door would not close completely.

  • Customer: Ronald from Reno NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1. Watched the video on how to make the repair. 2. Used the tools recommended. 3. Followed easy instructions as demonstrated on video, and Viola! It was repaired.

Fridge cam broke, door barely closed and crooked

  • Customer: Charles from RIO RANCHO NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only problem was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.

Refrigerator Door Won't Self-Close

  • Customer: Jan from Westerville OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First off, Parts Select has a great YouTube video showing exactly how to replace this refrigerator hinge cam. This repair was for my sister's 20-year old GE refrigerator. I used to do this same repair every 3 years on an expensive fridge my wife and I owned - one that had additional wood panels mounted on the door. The panels exceeded the hinges' designed weight limit, so every 3 years I replaced the bottom plastic hinge cams. On that fridge, I could replace BOTH interlocking hinge cams - one pair on each door. On my sister's fridge, the bottom cam of the pair appeared to be riveted onto the frame - rendering it impossible to replace. You may be able to replace both interlocking cams or only the top half cam. You won't know until you lift the door off and look. The bottom cam sits at a 90 degree angle to the door cam and it remains attached to the bottom frame of the refrigerator. These are easy to replace and their design is ingenious. The job is simple and well worth tackling if only to see how your door works. My sister's bottom cam was worn out, but not broken. The blessing: replacing the top half of that cam - the part attached to the bottom of the door - allowed the door to open and close LIKE NEW! The door worked perfectly and I'm thankful to Parts Select for having the hard-to-find cam and for shipping it overnight to me while visiting my sister in Ohio. Now her 20 year old refrigerator door closes on its own, tight as a drum, as if it was brand new. To be safe, I ordered (2) pieces - the matching top and bottom of the pair - but due to the rivet, could only replace one cam. The original $3 "fiber" shim was still good, but I replaced it anyway. I recommend taking cell phone photographs as you go so you know exactly how to re-assemble the three or four interlocking parts of the hinge. I referred to my photos as I re-assembled the new cam. Clearing items off the fridge door: 10 minutes. Removing the shelves, unscrewing the top and lifting the door to the counter: 10 Minutes. Disassembling the hinge, cleaning the area and reassembling the cam/hinge: 20 Minutes. Cleaning the bottom cam area of the Fridge mount and re-mounting the door: 10 Minutes.

Door would not shut tight

  • Customer: Peter from Tarrytown NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Followed Partselect video on how to replace cam riser. Very, very helpful!

Strange noise when opening/closing right side door

  • Customer: Benjamin from Plano TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched your video a couple of times, just to be sure I had the sequence down pat. The repair followed the video exactly and was completed in about 12-minutes. I was a bit leary whether I would be able to handle the door weight and alignment but it all went into place without any problems.

Door closing cams broken

  • Customer: Daniel from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
This job would have gone a lot faster if my father, Daniel Stewart would have let me replace it. He has trouble seeing and moves very slow. However, I have learned to be very, very patient. LOL!! One thing, I only ordered 1 because we thought that was all that was needed. It required two. Both were worn out. I do not have the model number off hand, it is a side by side, 16 years old.

broken cam riser on the bottom of the door

  • Customer: Charles from Anaheim CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I ordered a cam riser for the refrigerator door. I watched the "how to" video the day I ordered the part. It took about a week to get the part, but I was ready when it arrived. The 'how to' video was a big help. It showed me how to take off the door and replace the part. The process was quite simple! Oh! Don't forget to turn the refrigerator on again!

door would;ent close tight

  • Customer: Terry from Port Angeles WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced door closing bottom cam
All Instructions for the CSC24GRSBWH
886-900 of 924