Models > CSC22GRAAD > Instructions

CSC22GRAAD Hotpoint Refrigerator - Instructions

All installation instructions for CSC22GRAAD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSC22GRAAD
391-405 of 413
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Freezer work refierator compartment is warm

  • Customer: KIRK from Malibu CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.

Damaged slide on crisper drawer

  • Customer: ERIC from DAYTON OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pretty simple, just take out 2 screws and replace.

Refrigerator door didn't close without a big push.

  • Customer: Susan from Chevy Chase MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took door off. Replaced two cams at bottom of door, referencing those on the bottom of the freezer door. Also followed a video on the net. Worked like a jewel!

Bad switch for door prevented interior light from coming on

  • Customer: Patricia from Sylva NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Door would not close properly at the last few inches, now it closes good at this time but now need to be raised up to the 5/8 inch as the book says, haven't done that yet

  • Customer: Carol J from Alexandria KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the door closing cam works fine.

broken light switch

  • Customer: Francis from Holmes NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Popped out the old one and put in the new one it took five minutes.

Self closing upper and lower cam had broken

  • Customer: Charles from Metropolis IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
I removed the lower cover plate and placed a small scissor jack (used my car jack) under the refrigerator door, loosened the upper hinge, slightly raised jack to take the weight off of the lower hinge, removed the hinge with a 5/16 nut driver and the cam with a 5/16 socket. Installed new hinge and cam, removed door support and secured top hinge, check operation. Worked GREAT, did not have to remove door.

bad fan motor

  • Customer: theodore from salisbury NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
take fan out,put new in

Broken Bottom Hinge

  • Customer: William from MIDDLE POINT OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Empty all the good stuff stored in the door. Remove top hinge, lift off door. Remove bottom hinge from door and refrigerator, replace with new hinges. Replace door and reinstall top hinge. Very simple. Worst part was removing all the stuff stored in the door then putting it back! My parts arrived very quickly and I'm very pleased with Part Select.

Door would not close.

  • Customer: Daniel from Cherry Hill NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
With my wife's help, we emptied the door shelves and removed the door to the kitchen table. The video and instructions for replacing the parts were 100% right. We probably spent more time cleaning the door bottom and gasket than actually changing the hinge assembly! The job went very smoothly and saved us from overspending on a repair to this old fridge, or worse, making a quick decision on buying a new one.

Refrigeratior door of side by side would not close

  • Customer: Alison from Lincolnton NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I viewed a how-to video on partselect.com. I removed all items from the door shelves. Used a screw driver to remove the top "hinge" plate. Used a nutdriver to remove the door hinge plate. Removed door, laid on it's side-hinge side up (if you don't have a helper, lay it on a flat service). Simply removed the broken bottom plate and replaced with new part, and reinstalled on refrigerator. Super Simple!

The girlfriend opened the door and then it wouldn't shut on its own or stay closed

  • Customer: Gregory from Ontario CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Empty door first then take a phillip heads screw driver and unscrewed the top hinge cover 1 screw. Then used 5/16 nut driver to loosen top hinge from fridge. remove door by lifting and then lay on table to replace the lower washer that is held in by 2 screws and you only need to loosen one all the way leaving one in to align then replace and tighten it up your done.

Drawer Slide Rail cracked/broken

  • Customer: William from Bossier City LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video supplied by manufacturer and followed the instructions. Very easy.

Door would not shut tight

  • Customer: Peter from Tarrytown NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Followed Partselect video on how to replace cam riser. Very, very helpful!
All Instructions for the CSC22GRAAD
391-405 of 413