Models > CREA400ACW > Instructions

CREA400ACW Admiral Range - Instructions

All Instructions for the CREA400ACW
346 - 357 of 357
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bake element burned out
Remove racks, remove 2 screws, pull element out, disconnect connectors, reinstall new element.
Parts Used:
Oven Bake Element
  • Donald from Largo, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
heating element went out
part was sent quickly and it was easy to remove and replace. also watched video
Parts Used:
Oven Bake Element
  • kim from rockford, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Baking element blow out
Turn off the oven and let it cool. Remove the door by pulling it upward. Remove the racks and pull out the drawer under the oven and set aside. You should be able to reach the electrical wall outlet. Unplug the unit. Unscrew the metal tabs holding the element to the rear of the oven. Pull the element out about 2 inches so you can reach the clips attached to the wires. This is why you must unplug the stove. Wiggle the clips until you can pull them off the element. Don't let them slip back into the insulation. Bend them upward if necessary. Replace with the new element. Put on the clips. Ease back into the insulation. Replace screws. Plug back in and you are good to go.
Parts Used:
Oven Bake Element
  • Evelyn from Henniker, NH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Burner element stopped working
The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.
Parts Used:
Surface Burner Receptacle Kit
  • Robert from Lodi, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Porcelan Electric Burner Plug broke
The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.
Parts Used:
Surface Burner Receptacle Kit
  • John J from Coatesville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drip bowls were all rusted.
Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch
  • Robin from Seneca, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
burners would not come on without moving them around
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing
Parts Used:
Surface Burner Receptacle Kit
  • Ronald E. from Marissa, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Front 8" stove burner got excessively hot at any setting
Performed repairs just as you directed. Everything went in in without a hitch. All the parts fit well and seem to be working fine. Wife still complains. Maybe I need a new burner coil.
Parts Used:
Range Infinite Burner Switch - 8 Inch Surface Burner Receptacle Kit
  • John from Manchester, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rubber seal was broken
Broke the same day I installed it
Parts Used:
Door Seal
  • Jennifer from Lynn, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
The bake heating element burnt as I was baking some bread in x-mas just like a welding machine
I went to your web site and luckily I saw all the comments from people that had similar problems . It was awesome then I ordered the part and you had instructions on DIY . Great web site I will recommend it to anyone
Parts Used:
Oven Bake Element
  • Mario from Lutz, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
old drip bowl was worn out
new drip bowl fit perfectly and was a snap to install.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Richard from Germantown, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the old bowls were burned.
really easy.
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch
  • Rosibel from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CREA400ACW
346 - 357 of 357
Back to Top