CGS980SEM1SS General Electric Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
oven would not hest
-
Paul from Chicago, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Over wouldn't light.Broiler would.
At first I was ohms testing the wrong igniter ! I'm old school...so I assumed the drawer under the over was a broiler ( like my Moms was ) WRONG ! I was testing the parts on the roof of the oven instead of the ones under the pan on the bottom ! anyway, the lower igniter ohmed over 1 mega ohms. the spec I found was 60 to 1K ohms. Replaced the lower igniter and the oven works fine ! Thanks Part Select...great prices ! fast delivery ! That's why I bought the drip pans as well ! I will be a repeat customer ! ( FYI I'm a 44 year Auto Tech )
Parts Used:
-
Luke from Aurora, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
oven ignater
-
Sharol from Dallas Center, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Parts Used:
-
Mary from Redondo Beach, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
Oven Probe broke
-
Kathleen from Munt Laurel, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
burner cap did not fit burner, causing ignition failure
Replaced burner. New burner now ignites properly.
Parts Used:
-
Stephen from East Williston, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
oven would not lite
took off old initer and then had take off that little cover to get to the end of the wire so i could unplug it .thorugh it was kind of britale it fell apart abit .plug the other one in and put it on &turn the oven on and it came right on!it went well.thank you
Parts Used:
-
Russell from Reidsville, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Parts Used:
-
Joan from Watervliet, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven took longer and longer to warm up, then wouldn't ignite at all.
Unpluged power. 1. Removed all internals from the broiler. 2. Removed (3) protective heat shields. 3. Pulled glowbar plug through the access hole behind the gas piping. 4. Unplugged the glowbar. 4. Removed two glowbar holding screws and remove the glowbar. 5. Waited two and one half days to recieve the new part. 6. Reversed the process. NOTE: It really was not difficult at all, and the new part was original equipment so except for the delay in identifying, ordering, and receiving the part the whole process was very quick.
Parts Used:
-
Richard from Patterson, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
it would glow, but it wouldn,t light
I took out the bottom broiler drawer and reached to the back of the oven. i loosened the screws,unplugged it and replaced the igniter and plugged it in and put it all together and it works great now.
Parts Used:
-
Robert from New Hope, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
My stove would not light at all.
It was easy I unplugged the stove but I left the gas alone. I used a flat head screw driver to take the oven sheet off. Then I unscrewed the oven lighter and the bracket holding it. Then I disconnected it and put the new one on. The hard part was letting the wd-40 dissolve for the rusty screws
Parts Used:
-
Jajuan from Kansas City, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Gas oven would not ignite
Using your information that was posted i order the part that was most likely the problem. The video was spot on for the replace part.
Parts Used:
-
Russell from Maple Shade, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Fails to maintain set temp.
watch the video. Do the repair. What could be easier. Bake some cookies just for a test.. I did it twice just to be sure. Thank you partselect. Rite part, rite price, fast shipping, arrived next day...............
Parts Used:
-
Ronald from Arkport, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
oven would not light,upon looking at igniter,I could see it was not glowing with attempted startup.
viewed your video(which was my exact model)saw where everything was and how to access it and in no time was up and running again.
Parts Used:
-
Richard from Cornish, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no problem to report
-
michael from spanaway, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!