Models > CGS980SEM1SS > Instructions

CGS980SEM1SS General Electric Range - Instructions

All installation instructions for CGS980SEM1SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CGS980SEM1SS
196-210 of 231
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The buld broke off in the scoket

  • Customer: victor from Henderson NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Had to replace the socket. Once I realized I had to move the stove away from the wall and do part of repair from the rear it went pretty fast. I removed 2 screws from inside the oven but had to remove the electrical connections from the rear. then replaced the socket, reconnected the electrical connections. and replaced the cover.

Oven would not ignite

  • Customer: LINDEN from Cleveland OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Opened oven door approx. 3 in and lifted off. Lifted out oven racks and removed 2 screws from bottom plate. Lifted back edge of bottom plate and pulled plate out from under tabs. Opened bottom drawer and reached to back of burner and unplugged igniter. Pushed plug up through opening beside of burner. Removed 2 screws holding igniter and lifted out. Reversed procedure put every thing back together Oven worked fine. 1/2 hour cleaning and 1/2 hour replacing igniter.

Broken plastic burner knobs provided by G.E.

  • Customer: Beverly from Dana Point CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slide new, better quality knobs into place.

Wouldn't heat up or stay heated

  • Customer: Barbara from Conroe TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I went online and checked out the video to see if I could do it. It was really easier than the video showed because my oven was a little different than the one shown. I did it like the video showed me. I love your website and videos will be a return customer.

Light burned out in upper oven

  • Customer: Shirley from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

gas stove woul not lite because the igniter was not getting hot enough to open gas valve to lite the gas jet

  • Customer: Michael from N Providence RI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just followed your video! All the steps were identical and it took me 15 to 20 minutes. Thank you, you saved me from contacting a repair man or having to purchase a new stove. My wife wasn't too happy she's been wanting a new range. The part was exact made to order no having to re-wire igniter using the old igniter plug. Hopefully not soon but I will be using you again in the future for any future parts. Thank you Part Select.

oven lit intermittantly

  • Customer: Larry from West Newton PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
remove racks-remove heat tray in bottom of oven-cut wires-use ceramic wire nuts (supplied) to reconnect--saved over $140.00 from price quoted by repairman

Igniter was not working. The oven would not light

  • Customer: JoAnn from Mt Vernon NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
A friend installed the igniter kit.

Oven Heating Slowly and/or Not at All

  • Customer: James from Croton on Hudson NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Made an educated guess that the problem was a bad oven igniter. Although the malfunctioning igniter still glowed red hot, it was not hot enough to open gas flow to the burner. USEFUL TIP: the new igniter's plug was not a smooth fit with the oven's plug - I somewhat forced them together and sure enough - no ignition. So, I cut the plug off the old igniter, spliced it on the new one (fortunately, ceramic wire nuts were included by PartSelect), and everything connected up and worked beautifully. After that it was just a matter of screwing the oven floor panels back in, and a few hundred $$ were saved for under an hour's work.

Oven would not turn on

  • Customer: Manuel from Menifee CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Thankfully PartsSelect had a video that provided all the information on troubleshooting and instruction I required to install the new ignitor. Thank you! You saved me time and money and most of all the Wife is happy! Cause if she ain't happy then you fellas know the rest....lol Sincerely Manuel

I struggled with removing the plugged wires in front of hole.

  • Customer: Donna from Houston TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My Husband removed everything that needed the use of tools. I did the plug-in because of gentle touch needed on old parts. It went halfway on then Husband put muscle on it. We put all parrts back in place. I turned oven on and it came on quickly. Happy Wife! Happy Home!

ovem not light

  • Customer: roy from houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
seen film on installation instructions

oven would not hest

  • Customer: Paul from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
simple as 1 2 3!!!!!!!!!!!!

Over wouldn't light.Broiler would.

  • Customer: Luke from Aurora IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
At first I was ohms testing the wrong igniter ! I'm old school...so I assumed the drawer under the over was a broiler ( like my Moms was ) WRONG ! I was testing the parts on the roof of the oven instead of the ones under the pan on the bottom ! anyway, the lower igniter ohmed over 1 mega ohms. the spec I found was 60 to 1K ohms. Replaced the lower igniter and the oven works fine ! Thanks Part Select...great prices ! fast delivery ! That's why I bought the drip pans as well ! I will be a repeat customer ! ( FYI I'm a 44 year Auto Tech )

oven ignater

  • Customer: Sharol from Dallas Center IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I did not do it my husband did and it went very well.
All Instructions for the CGS980SEM1SS
196-210 of 231