Models > CG206B-E > Instructions

CG206B-E Jenn-Air Cooktop - Instructions

All Instructions for the CG206B-E
91 - 105 of 138
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
vent fan cloging up
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.
Parts Used:
Grease Filter
  • JAMES from McALESTER, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan switch was broken internally.
After reading the other do-it yourselfers I knew it wasn't going to be an easy task. However, when I received my new switch I saw that the hook up and installation would be a snap. My only problem was removal of the old lock washers so I cut them off with my tin snips and once the new switch was attached to the plate I used a socket on the end of a three inch extension. I placed the socket over the new washer and gently tapped on the end of the extention until the washer was seated. It took about two or three taps on each washer and I was finished. Everything went pretty well. Total time to install was about ten minutes.
Parts Used:
Fan Switch Kit
  • Charles from Santa Clarita, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner wouldn't light.
Took out a couple of screws and put in the new part. PartSelect was fast and efficient. Highly recommended.
Parts Used:
Front Burner Assembly - Black (Glossy Finish)
  • Clark from Tifton, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
simple swapping of parts
Undid the bad part and installed the new one
Parts Used:
Front Burner Assembly - Black (Glossy Finish) Rear Burner
  • lenny from east freetown, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old grease filter had hole wore through
Pulled the old one out & inserted the new one. Less than five minutes.
Parts Used:
Grease Filter
  • Michael from Mountain Iron, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worn out stove top
We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!
Parts Used:
Grease Filter
  • Redona from Roseville, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken hinge
Took the door apart and replaced the hinge, very easy
Parts Used:
Door Hinge
  • Don from Exchange, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace the grease filter!
Followed the directions. Piece of cake!!
Parts Used:
Grease Filter
  • Colette from Annapolis, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The paint begin popping of my original grill. My son had a friend that said that he could remove the old paint and repaint for me. Unfortunately in the shuffle of a motorcycle performance shop the grill was lost. I have been trying to get help from Jenn-Aire since March and they just kept saying th
Very simple for me!!! Open the box, uncover the new grill and lay it in its place.


Thank you so much!
Parts Used:
Vent Cover - Black
  • Norma from Salisbury, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnner rusty and will not start with electric start.
Removed and installed burners in less than 15 min with just a nut driver. Replacing the burn ere did not fix the starting problem, but replacing them did improve the hurried flame.
Parts Used:
Rear Burner Front Burner Assembly - Black (Glossy Finish)
  • Robert from Mary Esther, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Parts Used:
Grease Filter
  • Diane from Flower Mound, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace old dingy part
Part provided quickly and accurately
Parts Used:
Burner Grate - Black
  • Henry from Vancouver, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rotten filter for down draft vent
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!
Parts Used:
Grease Filter
  • Craig from Ashburn, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Downdraft switch on the top of the JennAir inkoperative.
I verified that there was current running to the switch.
Ordered a new switch,
Replaced the switch.
Had a little problem getting the oneway washers off the pegs but not much.
Saved the cost of a repair man and felt good about myself!
Parts Used:
Fan Switch Kit
  • Daniel from Fort Walton Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The paint had chipped and peeled on the inlet grill
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!
Parts Used:
Vent Cover - Black
  • Ann from Irvington, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CG206B-E
91 - 105 of 138
Back to Top