CFES365ES3 Frigidaire Range - Instructions

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

removed the old burner and put the new one in it's place.

Turn off breaker to the oven. Removed four knows by pulling them up and out. Using either a large flat blade screwdriver or adjustable wrench (depending upon stove top model) remove threaded style holders at each burner switch control to remove the glass clock control top panel. Remove glass panel and note ldgasket position. Place glass panel on top of stove top on a cloth towel to prevent scratches. Remove 8 screws and remove/lift up burner control assembly. Invert and place on its side to gain access to broken contol switch. Took a picture of wiring and close up off switch to help remember where each wire plugs into switch. Remove 2 Phillips screws from the old switch and remove from panel. Using a flat blade screwdriver gently remove one wire at a time and using knob to orientate the off position of the new switch. Remove each wire one at a time and install on the new switch. Compare numbers on both the old and new switch to assist where each wire goes. The numbers are beside each terminal and using a flashlight and magnifying glass will help making the job easier. DO NOT mix the wires up. Use the 2 longer screws and threaded bracket supplied fasten the new switch to the glass panel. Reinstall the glass panel using the screws removed and thread on clips at each switch and tighten using a large flat blade screwdriver. Be sure to route the wiring to not pinch the wires and install the gasket along the front edge which fills the gap along the burner top and side for a tight seal keeping water and food particles out. The infinite control switch has letters such as H1, H2 etc as the switch fits several models with different wiring diagrams and colours so it's impt to note this when transferring the old wires to the new switch. Also the gasket along the top glass edge ensure to note exactly how it is placed to reinstall to be exact when you reassemble. Replace the 4 control knobs by pushing them on after aligning to fit as they were removed. New switch should be positioned the same as the others with off at the top and a notable click. Be sure to note this when transferring wires from the old to new switch. Turn breaker on. Note: If you have minimal skills this should be left to someone who is an electrician or has repair experience in this field.

My husband followed the video instructions and it was easy to fix.

Turned off breaker to range then removed all element control knobs. Unscrewed retaining collars I suppose is a good word removed panel. Then removed bad switch installed removed one wire at a time and placed on new switch in proper places. Reassembled in reverse order turned breaker back on worked perfect.

Very easy just had to pull the wire up that holds it secure.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

I was required to remove the control panel to access the plug as it had been broken and the switch had been shoved into the unit . It would have been extremely simple if the plug had remained on the outside surface
My son can now clean his dirty oven

1 Turned off the oven breaker.

2. Removed the oven racks.

3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.

4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.

5. Installed the new sensor and now oven holds temperature steady.

Easy order, quick delivery and easy installation, happy wife.

removed replaced in lest than five minute

Drawings on web site somewhat hard to read, resulting in more
disassembly than actually necessary. Turns out, simply removing the
threaded plastic securing rings around the bases of the controls frees
up the faceplate, and allows access to the phillips screws that hold down
the bracket. Then it's a simple matter to replace the control unit by
swapping out the leads one at a time from old to new. Be careful when
re-attaching those plastic securing rings, they can cross-thread pretty
easily.

Remove 4 knobs from front of stove.

Remove plastic nuts that are directly underneath oven knobs. Loosen with plyers and unscrew.

Remove front cover.

Remove 8 screws holding down electrical panel. Remove panel. Remove 2 screws holding switch into place. Transfers wires from old switch to new switch so you hook them up correctly. Then reinstall in reverse order. Job complete in 15 minutes.

I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great