CDE852 Maytag Range - Instructions

I enlarged the vent access hole from four (4) inches to five (5) inches to accomodate a larger pipe. I then purchased locally a 5" to 4" transition and installed it in the enlarged opening, and sealed the space with expanding foam for a bug-proof air-tight fit. On the inside of the house I attached a short length of 4" pipe to attach the dryer vent pipe. On the outside, in the place of the aluminum vent cap, I installed the 5" Jenn-Aire vent cover purchased from PartSelect.com. The new vent is large enough to completely cover the chiseled out masonry area, and the 5" outlet reduces air noise from the dryer, but best of all the new vent provides the high quality look I needed to match the brick of my new home.

Removed 4 screws under the top unit that holds the stove control knobs. Open oven door for better view. Tilt whole unit (width of stove) up and out of top flange. Remove knobs for timer and the two control knobs (that operate the range burners) nearest the clock. Take out the screws by these knobs, 2 per knob and then you can get the frame that holds clock unit out. Make a drawing of wires to replace on timer unit or as I un plugged one I hooked it up to the new unit. Make sure you have turned off range at your fuse box before working on stove. Works good as new now, I assume it was hit by lighting that also made me replace our garage door opener.

Finding part needed and quick shipping were great. Web site so helpful. Initial attempt to remove old part was troublesome because I took out wrong screws thinking I had to remove parts beneath burner. Once I figured it out, it was so easy.
1. Turn off power.
2. Remove 4 screws BELOW control panel (open oven door to see them)
3. Pull off 7 front knobs.
4. Lift out loosened panel.
5. Take out the two screws holding control switch to front panel. Note orientaion of switch.
6. Replace wire by wire to new switch.
7. Put it all back together. Make sure switch is put in same direction.
8. Turn power on.

Followed the instructions given by Paul from Mickleton, NJ. Very simple, no problem. Using two small blocks of wood to hold spring loaded hinges out while I replaced the door on the hinges was a big help. Thanks for the excellent delivery time. Great service.

removed 4 screws holding entire face plate. Rolled face plate up on top of stove and left all wires attached (many). removed 4 screws adjacent to clock assy. Removed control knob just on either side of clock assy and removed control screws (2 on each). removed wires attached to clock assy and transferred new assy. Re-assembled and set clock time.

Removed the blower assy. Removed the motor. installed the new motor. Reassembled the blower assy. The problem I had was getting the proper clearance for the squirrel cage blower fan to rotate without rubbing on something. I had to make shims for the mounting flanges of the housing to get it to work. Took a lot of head scratching.

The element plugged in to the cook- top.The cook -top was working moments after i unpacked the element. thank you.

Jim B.

Serviceman took out broken glass by removing door and separating front of door from back of door. He carefully removed all broken glass Then replaced with new glass and fastened door together . He did repair in 20 minutes. Oven is like new. Thank you very much for still stocking this part that allows me to keep my oven repaired.

Since the motor is larger than the original, remove metal flange; shim one side of housing with 3 washers per screw and reseal..simple! Works great.

Remove modular element from cooktop,place upright on bench and remove sheet metal screws. Lift glass/rim subassembly from modular heating unit (screwdriver may be required to carefully pry glass/rim assembly from heating unit) as it may be a tight fit. Inspect exposed heating unit for any noticeable damage, clean any debris resulting from cooking spills, etc. Use caution in cleaning area around heating elements so as to not damage insulation. Install new glass/rim assembly using original screws. Do not overtighten screws as this may distort the sheet metal assemblies. Install in cooktop and test for proper function.

Opened the oven door and locked the spring hinges in the opened position with two 10p nails. Removed the oven door. I dismantled the component parts of the door. I then removed and replaced the broken glass unit,reassembled the door, slid the door onto the hinges, tightened two screws to lock the door in place, removed the 10p nails, closed the door----- and that was it. Less than one hour. The job was accomplished using only a Phillips screwdriver.

Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.

Motor (Blower Motor Kit) Part Number: PS1569907
No instructions are included in the package from PartSelect. Disassembly from the main housing was relatively simple. I found that paying VERY careful attention to how the original motor was wired and mounted would pay off in correct re-assembly, conquering motor vibration and rubbing. Most of my project time was spent cleaning the rotating blade wheel from 20 years of grease build-up. On tools, I would have appreciated the inclusion, or availability as an accessory, of a long-stem correct-size allen wrench (used in removal of the fan blade wheel.) The job went well, and probably saved me $200 in service call and labor.

Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.

First, I removed the two screws holding the element in place. I removed the element from the connector. I then removed the trim ring and drip pan. I unscrewed the retaining screw holding the connector and pulled out the connector about three inches and disconnected the two wires leading to from the old connector. I removed the old connector. I then connected the two wires leading from the new connector and fasten the connector to its retainer with a screw . I reinserted the drip pan and trim ring and plugged the new element into the connector. I turned on control knob to high and tested the element., which glowed red hot. Job completed and customer very well satisfied..