CDE850 - Instructions

I simply watched the video on the PartSelect site. That made the repair easy and fast. It took perhaps 5 minutes to bring the stove back to life again.

Ordered new moisture sensor, 2 screws and 2 wires. Back in business.

After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

My dryer was made so the fan was not removable and I had to reach through a narrow opening in behind the fan housing to put the belt on the motor pulley. The problem I encountered was that I could only use one hand to push against the idler pulley spring while at the same time try to catch the belt and slip it under the idler pulley. It repeatedly slipped off and every time it did the spring and idler pulley would come loose, and I would have to realign the the idler pulley shaft and attach the spring. After the fifth time I left the spring off, pushed the idler pulley shaft all the way in and put scratch a mark on the shaft on the inside of the first hole it enters. Next I drilled 1/16" hole in the shaft where I marked it, installed the spring and idler pulley then slipped a small cotter pin in the hole I drilled. Now if it slips off I only need to reach back and push the idler pulley up and catch the belt.

I followed instructions from video -- although the model used in the video was different, the approach was similar. Really the only difficulty was laying on my back (72 years old) and, with one hand and through feel alone (work area was not visible), getting the belt on the drive sprocket and the spring loaded wheel.

Must remove 2 screws in the lint screen port anchoring the top of the dryer. Next the front panel of the dryer is removed from the machine by pulling up with a putty knife disassembling the clip holding the front in place. 2 more screws are then removed holding front panel of the dryer. The doors sensor switch is then removed freeing the front panel to be removed. At this point after the front panel is off and the top of the dryer lifts in an upwards position and you can now see the tub and the broken belt. The belt has to be reinserted around the tub into the pulley assembly before being pulled onto the motor. The pulley lifts upward towards the tub if it was put on correctly. It has to be placed underneath the pulley in order to have tension put on the belt firming the connection between the tub and motor. To reassemble just reverse what you have taken off in that order. Their is a DYI video which shows the process perfectly. Have a good one !

I switched the circuit breaker off at the electrical panel, removed the burner switch assembly (two screws) from the cook top. The burner switches are held in place by a single nut over the control stem. I unscrewed the nut from the failed switch, disconnected the four electrical leads (one by one) from the old switch and connected them in the same position on the new switch and replaced the nut. The clips on the electrical leads were oxidized/tarnished so I cleaned them with emery cloth to assure good contact with the posts on the switch. Replaced the burner switch assembly in the cook top, energized the circuit and the burner works perfectly again.

Loosen two screws to remove door. Removed outside trim and other outside screws hold center panel in place. Removed one screw holding hinge in place. Screwed new hinge in place. Re-attached center panel to outside trim and hung door. Easy enough.

Used a multimeter to determine that power was going to the surface burner infinite switch. Then determined that power was not going from the output side of the switch to the burner element. Turned power to range off at the breaker box. Removed eight screws total on range top, four on the cartridge side, two located on back of control plate where the downdraft vent is located and two on the double fixed burner side. Raised the range top to gain access to the infinite switch assemblies. Removed to torx head screws retaining the infinite switch and then disconnected the five wires on the bottom one at a time, making sure to replace in the exact location on the new switch. Installed torx screws in the new switch and installed all screws back into range top. Reinstalled cartridge and burners and turned power back on. Tested rear burner and all functioned properly.

My 31 yr. old grandson very carefully took the whole door apart. Took out the broken window and put the new one back in. He was very careful to put every screw back in the original hole. It took him exactly one hour.