CAV2050AWW Magic Chef Washer - Instructions

Exactly like the video told me to! Seriously, I watched once when I ordered the parts, watched it again just before I started the job, and played each step as I completed that step. It simply could not have been easier. Without the video, I doubt I could have located and released the latches on the top of the washer, but seeing not only where he put the knife but the motion he used to spring them made that step so much easier than I thought it would be. With your help, I only paid a quarter of what the repairman wanted to make this simple fix -- Thank you!

new water pump

Removed old pump, disconnected hoses and drained water. Put hoses on new pump and reinstalled.

Removed back inspection cover which was two screws,the pump with pully was right there. Removed the belt and three screws from the pully and pulled it out. Put new pully in tightened the three screws put the belt back on and the inspection cover plugged the machine back in turned it on and it ran perfect.

I followed the instructions on your video - it was very helpful! I would have never figured out how to take the top off without the video instructions. I released the top latches using the putty knife, removed the broken lid hinge & pin and installed the new ones.

Took off the lid unscrewed 4 screws and replaced with new parts. Very simple.

Repair went as described in instructions supplied and YouTube Video "snubber ring". I could not have removed tub springs without putting 72 quarters in springs before removing as seen in another repair video which made removal and reinstallation doable. I still don't understand how this inexpensive part can cause such a problem.

There was a crack in the black rubber hose attached to the water inlet flume assembly, and the assembly itself was cracked and falling apart. 1) Turned off water. 2) Lifted top cover up (pry up with flat screwdriver). 3) Disconnected hose. 4) Trimmed hose above the crack. 5) Replaced "spring" -type hose clamp with small automotive-style clamp. 6) Unbolted flume from under lid (2 sheetmetal screws). 7) Reattached hose to new flume. 8) Reattached flume to underside of lid. 9) Closed lid (light pressure downward required). 10) Turned on water. Total repair time: 10 minutes.

After reading several online posts about this problem on appliance forums and following the suggestions about how to determine what was needed (whether the inner tub turned freely (by hand) in spin mode or not. It didn't which apparently indicates the likely need for a new thrust bearing. I purchased the transmission pulley and bearing kit from Parts Select. I got it the next day, without asking for next day delivery! When I took the old parts off (easy: pull off the plastic cover, remove the circlip and everything falls off the shaft (if you are working with the washer just tipped up. Unfortunately, that was where my easy repair ended. The parts were entirely different! After looking and looking and thinking, I called Parts Select. They informed me that Whirpool, who makes Maytag had redesigned the parts. They didn't look like they would work, but I followed the directions which came with the kit and installed the new parts - three times. The last time the pulley stayed on and the washer spun as it ought. The problem was that even with the smaller of the spacer washers the circlip was extremely difficult to get in its slot. Anyway, now the washer works and I am pleased, even though I spent many hours on what ought to have taken perhaps 1/2 hour.

removed belt motor and tub would turn and pump would not. ordered new pump removed three screws removed pump and reinstalled. washer works like new

Watched video , after that there was no problem, really easy.

Had no problems taking machine apart following online instructions. At first couldn't find snubber ring because it was completely worn away. Once found it was very easy to replace. Only problem with putting back together was getting the first spring back on, after that it was a breeze. Machine up and running.

Washer was jumping around in the spin cycle to the point that it disengaged the water fill level hose which in turn caused it to overflow. I fixed the hose but almost immediateley it stopped spiining or agitating. I looked online to find that the jumping around was most likely the snubber ring ... the hard stop and squeal most likely the Brake Stator ... the no agitaion or spin was likeley the thrust bearing. I ordered the parts and were received in a couple of days ... by the time they came I had already torn apart everything and was just waiting on parts for reassembly. The instructions were concise and complete but I did benefit from watching a YouTube video on the repair. All the parts went together just like they were supposed to even with my limited mechanical skills. All I really used was a small socket set, a couple of screw drivers and a pair of pliers. Taking the Brake assembply is dangerous but can be done with no special tools if you buy a couple of 2 inch 10-24 screws to replace two of the short ones and then back them out slowly (look for a youtube video on this procedure EASY!) ... took me a couple of hours but any one who has used a screw driver more than once could probably do it in under an hour. Washer now running like new ... No Jumping!!! People at Parts Select were Great!!! BTW ... So that the springs would be easier to re-install, I stuck about $50 of quarteres between the coils before removing ... worked Great!

The repair was easy. 5 minutes after grabbing my tools the job was done. It was easy to find the part I needed on the web site.

..watched the video..easy as pie..took longer to figure out what part was making noise than to fix..