Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Turntable gears stripped out, quit turning
I ordered the part on Thursday and received it the following Tuesday morning. Taking the cover off the bottom of the microwave was really the biggest part of getting this done. There are a couple of special screws on the back that a regular screwdriver won't fit into, but I got them off with a pair of needle-nose pliers. Unplugged the motor, took out one screw, lifted off the bushing inside the oven and just reversed the process to install the new motor. Piece of cake! Putting the cover back on is the most time-consuming part, do it in the right order and finesse it. Food is going quietly around now!
Unplugged microwave (make sure you do this!) Removed screws along front bottom of microwave, dropped panel enough to get to the motor. Motor is held on with two srews, take them out and remove the two spade terminals to motor. Reverse directions to install.
I removed three screws to drop the panel that holds the lamps and filter. I removed one screw that held the motor in place and removed the jack that powered the motor. I reversed this procedure to put everything back in place and everything worked just fine.
I downloaded the repair instruction as directed by your group and proceeded to complete the repairs. The wife had gone shopping so I was able to pull the unit from the wall and made the motor change quickly. If she were there to supervise I would still be doing the repairs. It was simple to search for the parts and order the material. I received the parts in about two days so this really impressed me for the delivery time. If I were to complete any other repairs on appliances my first stop would be to your location. Thank you for saving me from buying a new unit.
The inside latch for the microwave door broke, preventing the push button from working and the door from opening.
The built-in microwave was removed by taking off the front plate that was secured by 3 screws at the bottom. The unit was moved to the side slightly so that the power cord could be disconnected. Then the entire unit was withdrawn. The outer shell of the unit was taken off by removing the six screws holding it in place. The shell may need to be shifted slightly to separate it from the unit. Once removed, the bracket latch and opening mechanism for the door was revealed. The latch is inserted simply by aligning the two nipples with the correponding holes in the opening mechanism and gently pushing it into place. The latch is plastic and appears to be vulnerable to breakage over time through constant use, so I have ordered a spare should the problem reoccur.
All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott
You have to remove the cover which in my case was a little more difficult because the unit is wall mounted and has a frame around it. That was the hard part. Once the mounting frame was removed, you can remove the cover and the light bulb is on the top right side of the unit. One screw removes it and the new one pops right in. Put the case back on reinstall it in the wall and voila...piece of cake.
you will a security socket T20. this unit was installed over oven, remove trim cover,remove screws holding unit in place,I used a helper to get the unit out, once out you have to remove all the screws holding the cover on,on two of the corners they use a security hex screw so you need a special socket for that. remove the door latch switch,take your time or you will break tab holding switch in. ask me how I know.but super glued broke piece in place and plugged wire back in.the new latch may have a second pin but look at old one and plug wires in the same way.the light bulb does not screw out so I had to purchase the entire unit.total cost under a $100.00 to do repair.
The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.
Motor quit working but light and timer still worked.
Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.
remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced
hardest part was taking the microwave down off of the wall to gain access to the diode. Thought if was the transformer but ended up being just a blown diode. remove and replace and bench test. that part took 15 minutes . moral of the story don't boil water under the side of the microwave that holds the electric components.
We got a a carbon steel but and drilled out the stews and put in regular screws. We also had trouble getting the cover back on and ended putting 2 more screws on the left side which had none. The installation was the easiest part of the installation.