C221-C Jenn-Air Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Grease filter was torn and bent
-
Brent from Rancho Santa Fe, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
knobs sloppy and discolored and filter bent
This has been a wonderful cooktop and I could only hope todays quality is equally as good but after 25 yrs. I doubt it especially after looking at new dishwashers in the last couple of days. too sad. but these repairs were minor and no trouble. what amazed me most was ordering one afternoon and the parts were here the following day ! great service
Parts Used:
-
Robert from Meredith, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electric grill would not turn on.
Removed 2 screws and i nut. Unplug the old switch and plug in the new switch and presto, back in business. Extremely easy. Part was exactly as pictured. Part arrived within 2 days. Great Co. to buy parts from. Highly recommend Partsselect.
Parts Used:
-
Anthony from Tribes Hill, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs were worn and illegible
Removed the old ones and snapped on the new.
It was a snap and what a difference! Even though the cooktop is over 20 years old, it looks new again. Thanks to the knowledgeable support people at Part Select.Com we picked the right knobs the first time.
It was a snap and what a difference! Even though the cooktop is over 20 years old, it looks new again. Thanks to the knowledgeable support people at Part Select.Com we picked the right knobs the first time.
Parts Used:
-
Denise from Huntington, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My 8 inch stove top element would not heat
I first replaced the element and the receiver. This required splicing lines which was very easy. It still did not heat (even though my element indicator light was on) so I replaced the switch regulator. This took a little time because of the small space on my model. In fact, I had to replace a wire that had shorted by splicing a 3 inch section into it. When that was done, I simply re-connected the 5 wires in the original positions and reattached the cover. It works like a charm and my wife is delighted because we are hosting a family reunion/baby shower tomorrow!
Parts Used:
-
clifford from mead, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
20 year old countertop - dials unreadable
Two dials available, chose the wrong one, PartSelect paid to have the wrong ones returned and issued credit, while helping to select the correct ones. Friendly, REAL people, who absolutely sealed the deal. I'll always check here first for parts, filters, anything. Thanks PartSelect
Parts Used:
-
Carolyn from Fulshear, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
switch body that supports mounting nut broke
removed cover, pulled out old switch, moved each wire from old to new switch, mounted switch, replaced cover.
Parts Used:
-
Jon from GREENFIELD, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The switch for the fan on ourrange failed.
First I turned off the power to the appliance. Then I took off the face plate where the switch and burner controls are mounted (took off 2 screws). Pulled the assembly out as far as wiring would allow and removed the two wires from the switch followed by removing the two nuts that hold the switch in place.
I reversed the process to install the new switch, turned the power back on and that was that.
I reversed the process to install the new switch, turned the power back on and that was that.
Parts Used:
-
Jack from Redmond, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
vent fan cloging up
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.
removed cover pulled out filter ,replaced it with new one.
Parts Used:
-
JAMES from McALESTER, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace the grease filter!
-
Colette from Annapolis, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The paint begin popping of my original grill. My son had a friend that said that he could remove the old paint and repaint for me. Unfortunately in the shuffle of a motorcycle performance shop the grill was lost. I have been trying to get help from Jenn-Aire since March and they just kept saying th
Very simple for me!!! Open the box, uncover the new grill and lay it in its place.
Thank you so much!
Thank you so much!
Parts Used:
-
Norma from Salisbury, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad switch
-
Merwyn from Kingsport, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Parts Used:
-
Diane from Flower Mound, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
front burner would only work on high
-
william from cairo, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wife left burner on
-
Alan from Alpine, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!