C206 Jenn-Air Cooktop - Instructions

Pulled out the old burner and plugged in the new!

Replaced the drip pans

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

Disconnect power cord first. I remove the air fan cover to get to the two screws which hold the fan switch and burner knobs. Remove burner knobs and and remove switch cover, disconnect wires to fan switch. Pry spring nuts off with screwdriver to get switch off. Pay attention to which way switch goes on so that it turns on in the right direction. Install spring nuts (they may look too small but they're not) using a deep small socket the size of the spring nuts tap the the socket with a small hammer and the nuts will be locked in place. Put everything back in place and your done.

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!

First the power to the cooktop was turned off. Two screws were removed to be able to lift the fan switch holder. The old switch was removed easly because it fell apart. The nuts holding the part in broke as they were removed so they could not be reused. The new switch was put in place however the nuts were too small. I don't know what they were supposed to fit but not these screws. The part was super glued in place. It works perfectly.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

just installed

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Pulled the old one out & inserted the new one. Less than five minutes.

Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disconnected all the wires at once.
gc.

We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!