C206 Jenn-Air Cooktop - Instructions

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

The video you provided was excellent! Turned the circuit breaker off. Removed four screws, pulled out control panel, took a picture of the wiring to be safe. Disconnected the wires from the damaged control and removed it (two screws removed). Mounted the new control, connected the wiring, replaced the control panel and the four screws. Circuit breaker back on, turn burner on. That's it. Thanks for the video!

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

easy, drop in

I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)

I removed the cover plate for the burner switches and verified the wiring on the other switches. I had removed the bad switch a few years ago and I needed to make sure that the wiring was correct. I did not keep the original screws that hold the switch in place, because I destroyed them when I first removed the old switch. The were corroded from years of cleaning solution. I made new screws from longer wall socket screws by shortening them with a hacksaw. The entire process took about 30 minutes to do, and the results were good. The new switch is smoother than the others, but functions exactly the same.

James is an electrician so he istalled the part himself

We watched the video demo & followed it step by step. The project took about 35 minutes and we replaced the hinge on each side of the oven. First we removed the oven from the wall, then dismantled it & cleaned it thoroughly, removed the old hinges and replaced with new ones. the only problem we had was that the pin holding the hinge open was missing on one of the hinges, but we cut a nail and inserted it to hold the hinge open. The job was completed quickly, and the oven door fits and works well. Thanks for the video--it really helped us.

Just followed the instructions on this site... :) Unscrewed the front, removed old unit taking care of which wires went where, put in new unit. Voila.

Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.

New receptacle element. I am a girl and I did it.!!!!

Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done