C102 Jenn-Air Cooktop - Instructions

Loosen two screws to remove door. Removed outside trim and other outside screws hold center panel in place. Removed one screw holding hinge in place. Screwed new hinge in place. Re-attached center panel to outside trim and hung door. Easy enough.

Read privious fixes. Didn't know which control was bad but ordered two new ones. Marked locations of switch contacts and wire colors. Removed old controls. Installed new replacements and everything works fine. Thanks.

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

Replaced oven gasket and both oven hinges. Repairs did not work. Oven door is actually worst. Do not waste your time replacing the oven hinges unless they are actually broken. When to Ace hardware and bought a package of 3 super magnets for about $10. Practice placing the magnets on metal strip on outside of the actual oven vs the oven door. This metal strip is not galvanized for which the oven cleaning latch goes through. Appeared to solve the problem. I then used epoxy glue to insure the super magnets would permanently stay in place. These are dangerous magnets that must be kept away from children and pets. You will spend more time separating these magnets from each other than gluing them in place. This part I will let you figure out but the only way to separate the 3 magnets from each other is the slide them, one at a time, from each other. Now I am awaiting 4 to 6 hours for the epoxy to cure. Best of luck. Jeff

Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

Turn off the power!!! Remove two screws from back of switch section and pull toward you. That was the tricky part; it wasn't obvious to me how to remove the section. Then simply revmove the witres from the old switch one by one and put them on the new part. Close it up and you're good to go.

Turn off circuit breaker to cooktop. Remove 2 screws that hold switch plate assembly.Remove tinnerman nut from old switch using adjustable wrench. Remove one wire at time from old switch to same location on new switch. Return shaft back through hole and replace nut, be careful to not overtighten. Replace control know, turn circuit breaker back on and test. Works like new. Neil

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!

I purchased a replacement. I unplugged the cooktop. Unscrewed the little instrument panel and pulled it out. Turning over the panel, I noted the wires to the switch and photographed them in case I need to check them later. I pulled them off of the old, broken switch and put them onto the new switch, one at a time so that I couldn't get them messed up. Once all of the wires were switched, I removed the old switch and put on the new one. I then plugged in the model and tested the switch. It worked perfectly! IMPORTANT: I then tried to slide the panel back into the cooktop but forgot to unplug it first. This was a huge mistake, causing a nasty flash of electricity and smell. I unplugged the cooktop, put the panel back in, and replugged the cooktop. It worked, fortunately. Moral: ALWAYS unplug the damned cooktop when working on it!

I watched the youtube video that was provided by this website on my computer while doing this repair step by step. It was a snap!

Wife installed them, they just snap into place on the Rock Grate.