Models > ATF6000FS1 > Instructions

ATF6000FS1 Frigidaire Washer - Instructions

All installation instructions for ATF6000FS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF6000FS1
166-180 of 208
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Not Draing Water

  • Customer: Sammy from Notasulga AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Good

both shocks on drum was broke.

  • Customer: Kenneth from Effingham SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took cover off bottem on front of washer and pulled pins out of shocks. Put new shocks in and put the pins back in and reinstalled the cover. It was a easly fix and looking up the parts needed and ordering them was made easy by PartSelect.

Washer Stuck in Pause Cycle

  • Customer: D. Patrick from Vacherie LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The door assembly did not fix the problem this time, it was the control panel that had to be replaced. I have replaced the door assembly in the past, and I am glad I have a spare on hand. They do go out over time from the pressure of large batches of clothes. I am "no repair man", but having someone come out to replace it for you is a $300.00 job, easily. Read the tech info for your error code and go from there.

broken door strike

  • Customer: Willliam from Cottage Grove OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
(2nd time) replaced door strike with a Philips screw driver. Contacted Frigidaire and their customer service offered to pay for the part but I would have to have hired a service man to do the job. No thanx to Frigidaire. Also I suggested that their product development re-design the strike. The problem was a result of the hinge not firmly mounted. I researched the problem to find that others have had the same problem with this particular washer. Frigidaire's Affinity

door wouldnt stay locked during cycle

  • Customer: Phil from sun lakes AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took the top off removed the old one and put in the new one.Works great!!

broken suspension spring on side load washing machine

  • Customer: Jared from Spanish Fork UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I found you web site online found the broken part. I was pleased with a timely delivery and the correct part. A $30 dollar part from you saved me at least $150 from a appliance repairman. Thanks - Jared

Washer pump out

  • Customer: Dorothy from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Was so easy the video link made it even easier. Will with no doubt return for any other problems for my appliances if needed.

Washed a pliers in the pocket of my pants, and shattered the inside glass of the door panel.

  • Customer: JaNann R from Claremont SD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simple removed the screws from the door, did this the night I broke the glass. Gently pryed the inside of the door apart from the front of the door panel. Lined up the arrows on the edge of the new glass panel with the inside of the front door panel and placed the inside plastic door panel back on, to hold the glass panel in place. Replaced screws. Everything worked great! Easy, affordable fix!!

The Part was very difficult to reach from the top.

  • Customer: Cindy from Sacramento CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
There was not a video available on your site so I went to U-Tube and found one. Instead of reaching the part from the top I took off the rubber boot from the front and it was so much easier. Once I found and watched the video the entire repair took about 15 minutes. Now the washer works like new!!

Valve was split causing water leakage

  • Customer: BRENDA from BRECKENRIDGE TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The ONLY problem is the lack of space to work. I took out the dispenser tube to the left but even with that the bottom screw on the inlet valve was a LOT harder to get back in than out. After putting everything back together there was still a drip from the valve. So I uninstalled, used some liquid gasket material on the entire surface connection. Reinstalled n works fine.

Washer was leaking

  • Customer: Donald from Burlingame KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.

Vibrating Washer During Spin Cycle

  • Customer: Stephen from Sister Bay WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The video is very good. I have a stacked unit and didn't want to remove the dryer. It was difficult (but not impossible) to get the pins removed and replaced. I made a removal tool by drilling a 15/32" hole into the end of a 1"x1" piece of wood. Taping on this closed the pin safety and pushed it out.

missing a piece on the door

  • Customer: Amistad St from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Thank you.

Went into pause mode when starting

  • Customer: Fred from Wakefield RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Completed by my wife on line instruction video

Both shock absorbers were not working properly

  • Customer: Harold from East Peoria IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The video was helpful and gave good ideas to look for, it was harder to reach the pins holding each end. I used a 6-8 inch dowel rod to remove and replace the plastic pins. First time always takes longer than advertised but I wasn't in a big hurry.
All Instructions for the ATF6000FS1
166-180 of 208