ASD2123DRQ Admiral Refrigerator - Instructions

turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

Pull out plastic cover #13of refrigerator part discription (temp. control and light socket), snap out old light socket and replaced with new light socket. light is now working.

Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

First of all, I do not consider myself very handy. Most of my simple home repair projects include at least 2 trips to the local hardware store and take twice as long as they probably should. So if I can do this anyone can. For once, rather than just blindly throw new parts at a problem I did check the water pressure to the icemaker first and then even tested the icemaker with a multi-tester to determine what was wrong. I had $5.00 mulit-tester in my workbench but had never actually used it before, so I found step by step instructions on another website on how to test the motor and it turned out that one of the circuits in the main motor was in fact bad. Since the motor was around $80.00 dollars and the Whole unit that's inside your freezer is about $120.00 I decided it was best to just go ahead and replace the entire unit rather than just the motor. From what I saw online normally replacing an Ice maker is fairly simple. Remove 3 screws swap the prewired plug along with the metal arm then just reinstall it. Somehow whenever I try a home repair it's never that simple. First of all, our freezer is on the bottom so removing the screws holding the ice maker meant that I had to climb over, around and under the freezer shelves in order to get to the ice maker itself. Also one of the screws is not visible from the front so I had to hold a mirror in one hand while I tried loosening the screw with the other. Since the metal arm that turns off the ice maker is not included in the replacement it had to be moved over. Of course it was stuck, so it did take a little time to get it loose because I was being careful not to bend it and have to order another one. Finally installing the new icemaker meant once again that i was climbing over under and around the basket in the bottom level freezer. There is probably an easy way to remove the entire drawer but I couldn't find the release tabs so when just pulling harder on the drawer didn't work, I thought it best to just work around it. Still all in all, not a difficult job, just a little time consuming. The guy in the video did the swap in about 6 minutes, it took me about 45.

Installation was really easy since the replacement part was identical to the OEM part. Removed the three mounting screws with a nut driver. This allows one to remove the icemaker from the wall and disconnect the wire harness plug from the icemaker. I never unplugged the harness from the rear wall of the refrigerator. Put the new icemaker in place, making sure to place the water fill tube in the proper hole. Plugged the wire harness into the new icemaker and tightened the three mounting screws. The icemaker worked perfectly from then on with clean ice cubes and no leaks.

Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

Replaced icemaker by using total kit. Watched youtube video put on by partselect folks. Very easy to follow.

I checked the part number and an exact replacement was ordered. The old unit was removed and what I failed to note was that the water supply hose for the new unit entered from the side. Further examination showed a small "break-out" piece at the rear of the unit. but I still had to do something about the hole in the side. I used a piece of metal tape to close off that hole, trimmed it to size, and installed the unit. It was really an easy install after I figured out what to do about the hole. Evidently, this unit is mounted on the side of the freezer compartment in some models. Reading the reports of others was a big help.

I followed the video and advice from the many others on this site and only have a few additional comments. First, the decorative cover on the front of the old unit is held on with two plastic teeth on the top and bottom of the cover. This was not at all apparent and it took me awhile to figure it out. I used a sharp knife to pry up the top edge until the teeth lost their grip on the metal notches in the old unit. Second, don't try to pull the cables out of the front of the old unit before removing that cover. It is held in with a plastic snap that must be depressed after the cover is removed. The video does a good job explaining how to remove the old metal arm and attach it to the new unit so that it will recognize the ice level in the bucket. Finally, don't bother looking around the web site for a button that enables you to add to these comments. You'll be contacted by email in a week or two for that.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

I had to do this repair three years ago and found that the instructions provided by PartSelect were perfect. The video links provided this time on how to disassemble, do repair, and reassemble were extremely helpful. I followed those instructions and completed the job in less than one-half hour. The water now shuts down as it should. I really cannot add to the helpful write-ups by other customers. Thanks

Unplugged the refrigerator.Removed the nut on the front bottom side from the support bracket with a nut driver.Pull down and out the old icemaker but not clear out to remove the electrical connector reaching to the back . Re-used the old front cover and the wire support clips and the wire connector assembly.Also put the shut off wire on the new icemaker.Re-installed in reverse sequence and waited for ice cubes to be made.Make sure the water line coming in the back goes to the ice tray.

I took the old part out and put the new one in and it works like it should. I loosened two screws and took one screw out with nutdriver. then I used the old wiring harness, bail and cover to finish.