ARTSC8650E Amana Range - Instructions

First I turned off the circuit breaker on the house electricity panel. I removed the two screws that held the element in place in the oven. There were two wires connected to the element by spade plugs that were free floating in a fiberglass pad. I reconnected the spade plugs and put the element back in place and put back in the two screws. This procedure had I known what I was doing could have been done with the stove in place and would take no more than 5 to 10 minutes. Having no experience at this, I had pulled the stove out into the room and also removed the back cover which turned out to be unnecessary. I put everything back in place and held my breath and turned on the circuit breaker. Voila! It worked!

Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would check this out again when anything went wrong. they are great folks to work with.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

My husband replaced the bake element in moments. We couldn't get the broken light out of the socket because we couldn't locate our needle nose pliers. After a few days I finally got tired waiting and found a small pair of pliers in the house and got the remains of the bulb out and screwed it in, and plugged it in and we're in business!
Never wait for a man to do what you can do yourself!
I was so pleased that ordering the parts on-line was so easy and I didn't have an expensive repair bill to pay!

Turned off power to unit.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws holding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.

Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.

easy to put in

Purchased 2 piece broiler pan from this site

un-screwed 2 scrws and pulled out the old one and pulled off the 2 wires put the new one on the floor of the oven and hooked-up the 2 wires and pushed it in the back wall and replaced the 2 screws! done maybe 5 minutes

First turn off the electric breaker, and if necessary mark it or lock it so it will not be turned on while working on the unit.
I raised the glass stove top (it is hinged in the back), and propped it up with a piece of wood.
Removing the control requires the removal of a metal shield along with several mounting screws.
several wires needed to be removed, so I drew a diagram to make sure they all went back on the same terminals.
Reverse the order in replacing the control, and be ready for another 3 to 5 years of service.
This control is a universal part used on many different brands of ranges. Make sure you get the correct part before attempting this on your own because most parts supplies will not allow a return on an open electrical component.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together.
I am sure that I saved at least $200 in "labor".

1. Slide the Oven door out of its hinges after removing the screws - see Owner's manual.
2. Place door on floor with the inside face on the floor.
3. Remove screws on side and bottom of door and the lift away the side stamped pieces.
4. Remove screws as they becom visible and lift away the pieces till you reach the inside glass.

Remember the sequence and be careful not to strip the Phillips screws when unscrewing.

first I unplugged the stove,took the screws out of the pan that holds the element to the stove, then unplugged the element.then I plugged in the new element, then screwed the screws into the pan that holds the element into the stove. it was very easy.

Turned off the power! Unscrewed the element (2 screws) pullled the wires out. Put the new part right in. Easy!
Thank you-only a week before Thanksgiving, what a life saver! Also, order on Monday AM and was delivered by mid-day on Wednesday!

Pulled stove out and unplugged it (energized wire at burner even with burner turned off) Removed screws to lift cook top Removed burner support brace Removed three screws to remove burner Removed connections from old burner, installed on new burner Replaced screws in burner to brace Replaced burner brace Lowered cook top and installed screws Plugged in stove and pushed it into space