ARSE66ZBW (PARSE66ZBW0) Amana Refrigerator - Instructions

watched the video you have on installation and followed it with ease. The only part you need a tool is to loosen the first nut and then everything else pretty much pops out and you reinstall with the new part. The icemaker worked within an hour and makes perfect cubes. The videos are super helpful.

Take filter out of the box and open the refrigerator. Open the housing in the frig that holds the filter and twist the light-blue piece 1/4 turn, counter-clockwise. (Put the light-blue piece in a safe place.) Take foil away from filter. With 1/4 turn in the clockwise direction, twist the filter into its position. Let five gallons run through the system to get fresh, filtered water.

Followed your video instructions and tips. Real easy

Getting the old ice maker out was not difficult - it sits on a small ridge built into the freezer and then it takes three screws to attach it to the side of the refrigerator. Three important things to remember: (1) take off the metal bar that shuts off the ice maker from the old part, the new part doesn't come with the bar; (2) keep the screws and the cap from the old ice maker as they don't come with the replacement part either; and (3) make sure you put the water tube back into the holder otherwise it will pour all over the freezer (and not into the ice tray).

Simply replaced cover by hand. No tools required.

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

I wasn't sure about the part I needed so I called the service number, they help me decide on the correct parts for my unit. This was the easiest repair I've ever done. One hex head screw and one clip in electrical connection and we were done. It took less than 5 minutes and now it works like new, no more leaking water and plenty of ice.

I snapped the cover plate to the filter open. Pulled the filter down and twisted counter clock wise to take filter out. I installed the new filter in by inserting the filter and tuning clock wise to secure the filter. I flushed the water for about two minutes and then allowed it to be put back into service.

I simply followed the online instructions. Easiest repair job I have done. Once installed, which took about ten minutes, it was producing ice in less than two hours and is performing as it should. Had my frig not been a bottom freezer the installation would have taken less than five minutes. And to let everyone know, the on line instructions came in very handy during the removal process. Many thanks.

I ordered the replacement parts on line and received it a few days later. Thought I'd wait till the weekend to install the new parts. I expected it to take longer so I waited. Boy was I wrong. The hardest part was unloading the top shelf of the freezer. And it took longer to go get the nutdriver. I should have put it in immediately. Thanks for the instructional video. Works like a dream NO LEAKS. Will use your services on other parts as needed. Don from Pittsubrgh, PA.

Followed video advice

Removed malfunctioning icemaker and discovered that inlet water line was frozen. Thawed line using hairdryer and problem resolved. Returned new icemaker to PartSelect they promptly credited my credit card account. Problem solved.

I discovered that the water inlet was freezing, then the incoming water would run into the tray. I watched the video, then removed the ice maker. I discovered the the top two screwed just had to be loosened, not removed. I removed the bottom screw and move the ice maker to the side to disconnect the wiring harness. I found it to hard to disconnect. The pinch clips did not depress as they were supposed to, but the finally release. I did the replace without unplugging the refrigerator and it went fine. Took less than 15 minutes.

I removed and inspected the old unit and found the tray coating was flaking off. I ordered the new ice maker on line, One screw and rotate unit counter clockwise about 10 degrees unlocked it from the two snap in mounts. then unplugged the wire harness and it was free. Had to put the short wire harness on new unit, reverse removal steps and it is completed and working fine.

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.