Models > ARS15 Maytag

ARS15 Amana Refrigerator - Overview

Get Parts and Repair Help for ARS15

If you know the refrigerator repair part you need, you can browse the list of all parts on the ARS15, or you can search by name or part description. You can also find your part by where it is located on the ARS15 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ARS15 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the ARS15 [Viewing 4 of 4]

$2.52

Light Bulb - 40W

Sold individually.

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

$2.70

Screw

This screw is sold individually.

$2.70

Screw

This screw is sold individually.

$8.68

TRAY

$4.60

SCREW

$2.70

Hex Nut

Part may differ in appearance, but functions same as original.

$2.70

Speed Nut

$2.70

CLAMP- TUB

Gasket - sold by the foot

This gasket is gray and is made of a spongy material. This gasket is used for many air conditioners. It will come to you at the length you specify: one foot, two feet, whatever you require. When ordering over the internet, requesting a quantity of one will result in you receiving one foot of this gasket. Requesting a quantity of two will result in you receiving two feet of this gasket, and so on.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 88 of 91 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

noisy fan motor

  • Customer: robert from nashotah WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 17 of 20 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more

Refrigerator stopped cooling. Pulled it out of the alcove and plugged it back in. Compressor starfted but noticed condenser fan was not turning. Unplugged fridge and tried to turn the fan by hand - frozen.

  • Customer: Florentino from Windsor Locks CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 15 of 20 people found this instruction helpful
Remove the back hardboard cover screws for access to the condenser fan. I opted to tip the fridge over on its side for even better access to the fan mounts and wire. Replaced the fan assy (reused the fan). Splice the wire and it's done. read more