ARG7301W (P1143315N W) Amana Range - Instructions

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and placed them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.

Inside the oven: Pull the bottom floor pan off, just lift up in front and pull back.--Then take the one hex nut off the burner diffuser and lift off.--Remove under storage drawer. On Bottom of oven (Underside): Take off plate in back (2 ea screws) so you can unplug wire to igniter.------Go back inside oven and remove the 3 ea. screws that hold the igniter and holder/guard in place.-----Pull the igniter out.------Replace the new igniter in the holder/guard being careful not to crack the igniter.------Reverse procedure to re-install new unit.

I removed the bottom cover and the heat shield, then removed the screws that hold the igniter mounting bracket. After removing the drawer and the wiring cover I disconnected the igniter wires. I then removed the igniter and mounting bracket, pulling the wires through the hole at the rear of the lower burner box. I installed the new igniter by reversing the process.

We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it was done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!

Since the broiler was operational, this indicated the gas valve was probably functional since it provides gas to both the broiler and oven. I ordered the igniter based on other recommendations because the gas valve will not open until the igniter is drawing adequate current. This fixed my problem.

The burner has two screws holding it in place. I remover those and lifted the burner up. I then disconnected the wire attached to the igniter that was on the old burner and attached it to the igniter that was pre-installed on the new burner. I then placed the burner back into position and reinstalled the two screws. The reason that I bought the burner assembly is that I was unable to unscrew the screw underneath that held the igniter in place on the old burner.

Removed old igniter and replaced with new one.Tested oven and it went on. You need a phillips screwdriver to remove two screws and a small socket for the third screw to remove the igniter cage. Then pull out the wires from under the oven and disconnect. Reverse procedure to install new igniter. Reuse original connectors. Be very careful with the igniter because the tip is very fragile and can break easily.

after checking on line using model number and calling parts select ,the spark module was found to be defective, placed my order with them and at a very reasonable price replacedthe wires and module, very simple repair ,unplugging the range first I simlply removed the top by removing the two screws on each burner ,lifting off the top after disconnecting the wires from the burners ,carefule not to break the ends of the wires off and mixing them up, I simpley on screwed the module and removed each wire seperatly and replaced them one by one on the new module replaced the module on the range, hooked the wires up and presto done screwed downed the burners ,gas range works great thank you parts select for your parts and help,you saved me a bundle of money

Unplug power and turn off gas valve. Lower drawer removed out of way. Tilt back stove. Layed piece of wood under front with wife makeing sure not to fall forward. Remove back plate(2 screws)you will see the plug in. Unplug. Go inside of oven remove (1screw)bottom plate. See(3screws)remove igniter assy. Pull old out,replace new one (may have to pry bracket apart just a bit to slide in).

First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013

To access the igniter (bake, not broil) I removed the oven racks and removed the pan at the bottom of the oven enclosure (which just lifted out, not secured by any fasteners). Using a Phillips head screw driver, I removed the three small screws that secured the igniter and its shield to the burner. I then pulled out the drawer at the bottom of the oven, looked to the back of the space under the oven, located the igniter connecting plug and disconnected the igniter lead. I was then able to pull the igniter lead wires and plug through the hole at the rear of the oven and remove the igniter from the oven. This can all be done without moving the oven, I just laid on the floor and reached under the oven to disconnect the igniter lead connection. Once the igniter was out of the oven, I carefully removed the igniter from it shield by gently pulling the shield off, there were no fasteners to remove. I installed the new igniter into the existing shield, being careful not to touch or damage the delicate heating element on the igniter. Re-installation of the igniter was just the reverse of the removal process. The whole thing took about 15 minutes for this model of oven, even though I had never replaced an igniter before.

Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!

Removed the burners 2 screws per burner disconnected the wires to the burners. Lifted the oven top off removed original ignition module. Installed wires to the new module taking note of replacement location. Than mounted new ignition module. Tha only hiccup was dropping 1 screw down into the stove lining found replacement screw and installed module. Cleaned and replaced top. Mounted burners and the stove is working like new. Project proved to be quite simple and guick. Thanks to partselect for there prompt delivery and other peoples input on install made it quite easy and simple,

1. Remove the oven bottom inside the oven. 2. Remove the pan underneath the oven bottom by undoing one hex nut. 3. Once this is done the oven igniter is visible. It is located in a protective housing. 4. Remove the three sheet metal screws that hold the igniter housing in place. 5. To unplug the igniter remove the storage door. Underneath the oven there is a access panel. Remove it by taking out the two sheet metal screws. Once this is removed the igniter can be unplugged. 6. Pull the old igniter out of the housing and carefully install the new one in it. Careful the ceramic igniter is fragile. 7. Plug the new igniter in and screw the housing back in place. Changing the igniter was easy once we found the panel after removing the storage drawer that made it possible to unplug the old igniter and plug in the new one.