Models > ARB210BAC (PARB210BAC0)

ARB210BAC (PARB210BAC0) Amana Refrigerator - Overview

Get Parts and Repair Help for ARB210BAC

If you know the refrigerator repair part you need, you can browse the list of all parts on the ARB210BAC, or you can search by name or part description. You can also find your part by where it is located on the ARB210BAC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ARB210BAC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.82

Light Bulb - 40W

Sold individually.

$126.87

Ice Maker

This replacement ice maker mechanism does NOT come with a cover, a wire harness, or the mounting hardware. Must be ordered separately.

$2.70

Screw

This screw is sold individually.

$3.96

Rear Drawer Glide

$37.21

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$31.14

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

$17.47

Defrost Timer Kit - 120V 60Hz

The timer will shut off the cooling system of the refrigerator and the defrost heater will turn on.

$43.62

Oven Rack

Sold individually.

$2.70

Screw

This screw is sold individually.

$48.13

Bake Element

This bake element is found on the bottom of the oven.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 185 of 255 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 77 of 80 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

freezer door gasket needed replacing

  • Customer: Jeffrey from Palo Alto CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 76 of 90 people found this instruction helpful
Unplug refrigerator. Open freezer door. Lift the old gasket from the edge closest to the center of the door to expose the hex-head screws. Get a nut driver the appropriate size (1/4" if I remember) and loosen, but do not remove all of the screws. Once loosened, the old gasket can be removed. Slip the new gasket in just like the old one was. Lift the ed... read more