Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Exterior light bulb (PS2376034) broken off in socket. No access for pliers after glass cover removed.
Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place. Snapped off the top control panel which exposed the wiring connecting the control panel. Unplugged a couple of wire harness units to free the control panel. Be sure to label the units to know which goes where during reassembly. Remove the microwave unit from the housing and place it on its side. Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
I removed the microwave to install a back splash and found the support edge on the backplate had broken off and was missing. I searched for parts for the microwave and found them on PartsSelect.com. Easy to order, and was shipped promptly.
Once the part arrived, install was simple, lining up the existing holes. The only hard part was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.
bottom base got overheated and paint burned off-needed replacing
I removed the old base by unscrewing the12 screws and dropping down the metal bottom. I disconnected the light and unclipped the electrical wiring harness for the fan and removed the bottom base. I then reattached the wiring harness and light to the new base and reattached the base to the microwave with the 12 screws. It is now as good as new again!! Thank you for locating this hard to find part for me!
I had a cabinet person install new kitchen cabinets and counter top. After the demolition of the the old cabinets, I had to buy new parts for the new instal
I had the help of a handyman, I'm 75 years young but not handy with tools
Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.
open door, remove glass turntable, replace broken ring-turn with new one. replace glass turn with new one. thats how easy it would be if i had received the new ring-turn. this item weighs 10 to 11 ozs. i ordered this item on oct 13 and it arrived in martinburg WV on oct 15 and there it remained for THIRTEEN DAYS!!! before toward my destination. still no approx time of delivery. i assume that it will be delivered on oct 29 since it has reached a city in mississippi and i,m in a 15 to 20 min drive away. two stars is all that i can offer for this order.
Two Mounting plates # PS12074431 were sent to me and both do not fit. Model number MMV1175JZ-0 Serial number TRX-17. 24546 Manufactured April 2020 Contacted Maytag and even sent pictures to show the problem with alignment of the mounting plate not fit in the back of the microwave.
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
On Turning on the Microwave, it was sparking, was not sure where the sparks are coming from, initially I thought mica at the end of megnatron duct could be the issue
when I opened the back cover of microwave, the diode was kind of blackish blown, since there was light bulb and fan were still working, i thought it could be problem with any one of the components like; magnatron or capacitor or diode, so first replaced the diode and mica at the end of the magnatron duct, there was problem with door switch as well. i fixed that too. Now it is working. It cooks bit faster, Wondering why?
This is an under the counter microwave. Simply removed the two screws holidng the vent grille on top of the unit, lift out the old charcoal filter, clean the vent fan exit surfaces then replace the filter and put the vent grille back. Be careful to not drop either of the two screws after one is installed as you will have to take the grill off and start the screw installation again unless you have a magnetic to retrieve the dropped screw. An easy five minutes at most to change.