Models > ALY2280BDB > Instructions

ALY2280BDB Amana Range - Instructions

All installation instructions for ALY2280BDB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ALY2280BDB
1-15 of 47
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

gas burner ignitor failure

  • Customer: roy from East Providence RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 77 of 88 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.

The grommets came apart metal from rubber.

  • Customer: Frank from Pierce ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 16 people found this instruction helpful
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.

burner would not light; ignitor did not produce spark

  • Customer: Candace L. from Woodinville WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't have it properly installed at first. Anyway, very easy. Did it in my pajamas on a Saturday morning.

range top loose, grommets missing

  • Customer: joseph from wildomar CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 12 people found this instruction helpful
very easy to push each grommet into range top holes

The burner igniter would not spark to light the burner.

  • Customer: Margie from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
I had to unscrew 4 screws on the burner unit and then 2 screws on each igniter. slip the olds out and the new ones in and then replace all the screws. And wa la they sparked and I was cooking again.

Needed a second oven rack for RV oven.

  • Customer: Michelle from Silver Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 11 people found this instruction helpful
With a family of five a needed an extra oven rack as my RV oven is very small. After much aggravation between calling and going online to the manufacturer I still could not get any help. Even with locating the all important parts number. I was just about to give up when I was surfing around and found this website. Wow! What a relief! Not only did you show my where to find the part number, but I ordered it and got it within days. I spent more time on hold and online with the manufacturers customer service than anything else. From now on, no matter what I need, whether RV or home, I'm going staright to PartSelect. Thank You and my family thanks you too, as we wil be camping on Turkey Day and now I'll be able to get all the meal done at once! Happy Thanksgiving! God Bless

pilot light would not stay on after releasing the "pilot lite" light knob

  • Customer: john from aiken SC
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 5 of 6 people found this instruction helpful
First I turned off the propane tanks.

I then removed the two stove racks on the top of the stove and removed the metal cover surrounding the burner elements.

Next I detached the gas line and quickly inserted the temporary plug (supplied with stove) to stop the left over gas from entering the camper.

I then removed the two lower screws at the base of the stove just below the oven door and the two screws at the top rear of the stove securing the stove .

I now removed the stove.

Next I detached the pilot element from inside the oven and from the opposite end at the top of the stove at the burner area.

Now I replaced the element with the new one and replaced the stove all in the reverse order.

burner would not ignite

  • Customer: Scott from Sacramento CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.

Inside of knob busted out, would not turn ignitor.

  • Customer: DAVID from SEARCY AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Actually too simply to list as DIY job. Merely remove old knob and push new one onto spindle.

One of four burners did not start (no sparks)

  • Customer: Nataly from Brooklyn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.

Oven rack missing

  • Customer: Pauline from Weedsport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Opened oven door, slid in rack , closed door...
Fit perfect....

Igniter insulation had cracked and spark was shorting out on the flame holder whatchmacallit.

  • Customer: Melvin from Santa Maria CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.

missing gromet

  • Customer: Hal from National City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
Pushed into hole by hand, really simple

Lack of burner gas ignition

  • Customer: Andrew from Lufkin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.

Pilot would not light or stay on

  • Customer: Richard from Yuma AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
Replaced the pilot and tubing, this is a RV stove and oven. The easiest way to replace it was to pull the stove slightly away from the wall as the tubing had a securing strap to the back stove wall which had to be removed to get the pilot tubing removed and the new put in. That was the most time consuming. Anyone with some handyman capability can do this job quite easily. If you use part of the old end of the tube connection at the pilot as I did make sure that you insert the new small pin hole restricter (my term).
All Instructions for the ALY2280BDB
1-15 of 47