Models > ALW895SAC (PALW895SAC)

ALW895SAC (PALW895SAC) Amana Washer - Overview

Get Parts and Repair Help for ALW895SAC

If you know the washer repair part you need, you can browse the list of all parts on the ALW895SAC, or you can search by name or part description. You can also find your part by where it is located on the ALW895SAC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for ALW895SAC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.54

Thrust Washer

This washer is 3/4 inches in diameter.

Order within the next 1 hr and 58 mins and your part ships today!
$5.04

Retaining Ring

Sold individually.

Order within the next 1 hr and 58 mins and your part ships today!
$40.32

Drain Pump

This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.

Order within the next 1 hr and 58 mins and your part ships today!
$2.70

Hose Clamp

Order within the next 1 hr and 58 mins and your part ships today!
$6.91

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 1 hr and 58 mins and your part ships today!
$2.07

Lid Hinge Mounting Screw

Sold individually.

Order within the next 1 hr and 58 mins and your part ships today!
$19.16

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 1 hr and 58 mins and your part ships today!
$5.40

Hose Clamp

This hose clamp is sold individually.

Order within the next 1 hr and 58 mins and your part ships today!
$4.54

Spring Retaining Clip

This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.

Order within the next 1 hr and 58 mins and your part ships today!
$20.86

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

Order within the next 1 hr and 58 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 30 of 33 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more

Washer wouldn't drain

  • Customer: William from Fayetteville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench set, Wrench(Adjustable)
  • 19 of 19 people found this instruction helpful
I was doing laundry one day, and noticed that the washer did not drain. I drained the water via a shop vac and checked the hoses. There was a baby sock stuck in the hose leading to the pump! I cleared the jam and the washer finally drained again. Once I ran another load, the washer wouldn't drain. I repeated the procedure, and found that the motor was spinni... read more

Bearing went out causing lots of noise.

  • Customer: mike from hull IA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 19 of 21 people found this instruction helpful
This is not a bad repair, but give yourself some time. I did not have to take the tranny and motor out, but the inner and outer tub and all related parts had to come out, along with the outer tub base. If you are replacing the tub bearing, you HAVE to order the seal kit. Don't try to skimp like I did, since you will need the seal kit as this is what causes t... read more