ALG443RCW Amana Dryer - Instructions

Removed Timer Knob,,Removed 6 screws at rear top of control panel,Removed 3 inch metal panel at top of control panel,,then tilted entire assembly toward front of dryer to gain axcess to timer assembly.. Removed 1 screw holding timer in place and then twisted entire timer assembly counterclockwise to remove,,Installed new timer (note new timer latched in hole did not have to install single screw onto new timer) Switched wires carefully not to mix them up..

No work was required. I just slid the filter in a hole.

Had to call the repair center 3 time & view the video several times because the drum support roller would not fit on the new shaft. Even ordered the parts twice (with refund on first) to ensure the correct parts. The call in center could not help me & I was left on my own. I had to force the roller onto the shaft which was very difficult, Once the hole had gone onto the shaft, it was fine, but I had to take it off to install the shaft then gently drive the roller onto the shaft. It does roll free once over the outer edge. Installing the belt was not easy either. The video did not have a good picture of how the belt runs & not drawing was available, maybe it could be included next time for others

I only had to watch your video! The absolute BEST instructions ever. Your videos have saved me already $480 in repair bills in just one month. First my washer needed a snubber ring, and you had that video and then the dryer parts. Thanks again for being there!

Ordered thermal fuse and cycling thermostat

I don't have the model number right now, but you video was fantastic.

On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

The first problem i had is that the idler pulley went out for the dryer drum. Part of the plastic pulley melted and the drive belt eventually broke. I got the parts to replace the idler pulley and belt from PartSelect. That was a pretty easy repair, but when i had it apart I noticed a small crack in the aluminum pulley on the motor drive shaft, I'm assuming because of the heat generated by the seized up idler pulley. I put it back together anyway. The dryer made it for 2 or 3 batches of clothes and the aluminum pulley on the motor shaft came apart. Turns out the only way to replace that pulley is to replace the motor. The cost for the new motor wasn't all that much and the dryer is in otherwise pretty good shape, so I ordered the new motor. The motor assembly was easy to replace and works great. Glad I was able to get it fixed without too much expense. I literally spent less that an hour altogether with both repairs. I was happy with the parts and service from partselect.com, they also have great how to videos.

Really easy popped the lid with a flat head screwdriver, then marked wires for door light and switch, took 2 5/16 bolts to remove front door, then 4 bolts also 5/16 to remove front panel but be care ful and remove drum belt then take panel and drum out. Then took a set of ring pliers to remove wheel slapped new one on.then reverse sreps to assemble.

Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.

When I first heard it sqweeling I tokk off bottom cover and peeked around the turned it on and it seemed to be coming from a back roller,I sprayed a little wd-40 and it went away,for a day ! Then I found parts select on line and found the problem. The belt had worn into the roller almost to the shaft. I ordered the roller and belt and watched the very helpful video and it took about 15 minutes!parts $29. 00 Piece and quiet without calling service guy priceless !! Thanks steven l. I. Ny

Just like in the video. A very simple repair

removed bottom kick plate,then door and front drum seal support so i could lift top cover out of the way.took off belt and removed drum to get at support rollers.

I followed the video that you had posted. I don't think I could have done it without the video being posted. Thank you very much.