Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven light not working
I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!
Bake burner did not ignite. Had gas flow, igniter clicked but there was no ignition. Ordered iginiter.
I was able to perform this repair without removing the oven door. Removed cooking racks (2) Removed oven bottom (2 screws), removed flame spreader (2 screws). removed igniter (2 screws - used a 5/16 hex socket wrench). On this model range the lower screw on the igniter is on an angle (about 45 degrees) and very close to the heat reflector pan; patience and perseverance was required to remove it. - do not know if there is a special tool that would help making removal of this screw easier. If it wasn't for this one screw, the repair should take about 15-20 minutes. Replacement of the igniter solved the ignition problem.
gas burners would not automatically light when gas turned on
I went online and discovered the repair method and schematic of the range. I removed the spark module after first removing the upper rear panel cover and replaced with the new part module ordered from your company and now the spark module operates all the gas elements when they are turned on thus lighting the gas burners. My mother in law was thrilled, as she had been using matches and burning her finger tips,since the original range part malfunctioned. The only problem was the small screw from the original installation was not long enough , so it required some changes to get it affixed to the cabinet side.Thanks for the reasonable price and the right part for the job!!
Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.
Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Followed youtube instructions: lifted clips on door hinges, removed door. removed screws, removed rear cover, replaced right hinge. reassembled door. caution: door handle will fall off when top two screws are removed. Alignment of screws is some what difficult, requires awl. Replace door, return locking clips to forward position, check door for operation.
the part that fits on the stem to turn the knob had broken. I tried to tape it together, but that did not work.
since it was the control knob, all I had to do was to push it right onto the stem, and it was finished. Using the web site to find the correct item was very easy.