All Installation Instructions for Frigidaire Dryer AGQ7000CES0

Dryer just barely got warm

Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.

Parts Used:

M Series Ignition Coil Kit

J Martin from Guerneville, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

no problem

put door catch in hole

Parts Used:

Door Catch

David from Mayfield, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

banging noise

followed vidio instruction which made it easy

Parts Used:

Rear Drum Bearing Kit

gordon from creve coeur, IL
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dryer Vent Was Very Clogged and Impossible To Clean

Removed two screws, removed gummed up and clogged vent cover and replaced with new

Parts Used:

COVER

Mike from Covington, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Loud squealing noise until dryer heated up - then quiet

purchased bearing kit

Parts Used:

Rear Drum Bearing Kit

Ernest from Stockholm, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

The Rear drum bearing kit had sheared off

Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!

Parts Used:

Rear Drum Bearing Kit

Amy from salem, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dryer squeals while running

I wanted to know why my dryer was making such an ear-piercing screech. Googled, and found Steve at PartSelect. After watching the 10 minute video on how to replace the rear drum bearing, I knew this was something we could do at home. I ordered the parts on Friday and they arrived on Monday. Also ordered a new drum belt and drum glide. Didn't know if we would need those parts, but figured while we had the dryer apart, we might as well replace them. My husband watched the 10 minute video the following Saturday, and together we replaced all 3 parts. The original bearing was small enough to fit through the hole (which it shouldn't) and metal shavings we all over the plastic holder. The large metal ball attached to the dryer had grooves worn into it. The kids we amazed, too! I can't believe the repair was so easy! Seeing the inside of the dryer makes me wonder why they cost so much! Do not hesitate to make this repair yourself. Even just one person could do it.

Parts Used:

Drum Glide - White

Drum Belt

Rear Drum Bearing Kit

Jill from Norfolk, NE
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

Dryer Won't Heat Up

Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.

Parts Used:

M Series Ignition Coil Kit

Michael from Los Angeles, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Rear drum bearing failure

Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

Parts Used:

Rear Drum Bearing Kit

TonyMac from Alamo, TN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum

I remove the drum, and install the bearing just like the instructions in the video.

Parts Used:

Rear Drum Bearing Kit

Witly from Wheatley Heights, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

dryer would heat up but shut off too early

pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.

Parts Used:

M Series Ignition Coil Kit

D from Oak Park, IL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

dryer started to squeal when started

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

Parts Used:

Rear Drum Bearing Kit

Niel from Howell, NJ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

squeeking & thumping noise

i followed the video step by step & i never thought a repair could go so well thanks to the repair video

Parts Used:

Drum Belt

Rear Drum Bearing Kit

Thomas C. from Manahawkin, NJ
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Scraping noise at rear of drum

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

Parts Used:

Rear Drum Bearing Kit