AGD4475TQ0 Dryer - Instructions

I pulled up the "How To" on the internet and it gave me step by step instructions. I only had to deal with 4 screws. Yaaayy! It was a good experience and the piece was perfect.

Remove the lint filter. Remove top without disturbing control wiring -- turn top on end but make sure it cannot fall. Unhook contacts on door switch. Remove screws hloding front panel and kick plate. Remove door hinge springs. Remove front panel and kick plate.Fish out old broken belt. Remove drum. Vacuum out all the lint. Reposition/replace pulley assembly and wheels. Place new belt around drum. Reinstall drum being careful to properly position the seal at rear. Prop up the drum with a suitable sized article to keep it in position temporarily - or have someone else hold it in position. Thread drive belt through pulley assembly per directions and put over drive hub. Manually turn drum to ensure proper belt and seal positioning. Put front panel back on. Turn drum while inspecting seal -- use putty knife to slip under seal if necessary to ensure its not folded under drum lip. Remove the prop holding up drum. Reinstall door hinges springs.Reinstall kick plate. Reinstall top.

Replaced belt,wheels,idler arm and drive motor.Used video instructions from PartSelect.Instructions are spot on.All replacement parts were correct ans fit like a clove.Orderinig was esaey.Staff was friendly and knowleable.Parts arrived quikly with out using next day service.I will use PartSelect in the future and recomend the company to my coworkers and friens.

i first watched a video on U-Tube and did exactly as they did. removed screws from the lint tray, pried up the top panel of the dryer with my putty knife, unscrewed the 2 hex screws at the top, disconnected the plug for the dryer door,and installed the new belt it really was pretty easy. the only thing I would recomend would be when installing the belt put towel or anything that would protect your arm from the botttom piece of sheet metal. I got a pretty good cut on my forearm while I was putting the belt on the bottom pully.

unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.

Replacing the cycling thermostat did not fix the problem on my whirlpool gas dryer. I then did more research on the internet and found that a likely cause was the 2 solenoids coils that control the gas valves. I replaced these and this and now the dryer works great. I had no idea how to open up the dryer to get at these, so it took a little while to figure out. 1) Lift up on front of dryer top to pop top off of 2 spring clips. 2) Reach down through top opening and find 2 bolts that attach dryer front to dryer body and remove with a nut driver. 3) Lift up on dryer front to release it from 2 hooks that it hangs on. 4) Remove 2 screws for bracket that holds coils in place. 5) Unplug coils and put in new ones. 6) Reinstall in reverse order. Problem solved. Great service from your site. Received parts 1 day after order using regular ground shipping.

First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.

Found symptoms on Part Select website and confirmed that the problem was the coils. It was extremely easy to find and the site saved me hundreds of dollars on a repairman, labor costs and marked up parts. It literally took about 5 minutes to repair. Awesome site!!Thank You

Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.

raised the lid, removed 2 bolts from front face, laid dryer on its back,and replaced belt, very simple. took approx. 20 min.

Opened up the dryer, to discover the broken belt at the bottom, read model, serial number. Went on line, found sites that gave parts lists and diagrams. Wrote down part no. Used Safari to find the part. PartsSelect was cheapest, had it in stock, and could ship fastest. Sears was more expensive and slower. The part arrived in 3 days as promised.Overall, it was excellent service.

I have never done this before, so I watched the video and also watched a youtube video for this model to repair belt. Used a gallon paint can to hold up the drum, while I secured the belt. whoooo hooo I did it all by myself...59 yr old Female Do it yourself enthusiast! Thanks for all the information.

I had no idea how to take my dryer apart so it took me a little while to figure out. I hope by me writing this out my experience might help someone else fix their dryer instead of having to buy a new one. 1)I removed the lint screen assy by removing the 2 screws that hold it to the dryer top. 2) I popped up the front of the top of the dryer which is held to the dryer body by 2 spring type clips. Removed by prying up the top using a big screw driver to release it from the clips.3) Reaching through the top of the dryer and feeling down along the front there is one fastner on each side that holds the dryer front to the dryer body. I removed using a nut driver. 4) The dryer front then can be removed by lifting it up to release it from 2 hooks on the bottom that it hangs on. 5) The coils were located at the lower left side of the dryer as part of the gas heat assy. There is a bracket that holds the 2 coils in place using 2 screws. I removed these 2 screws. Then the old coils can be lifted off the valve post. Then unplug the electrical connector from the old coil and plug in the new coils. 6) Reverse the process to reassemble. After this my problem was fixed and my dryer is working great.

Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

I unplugged the dryer from the wall outlet and remove the two screws from the lint filter area, followed the instructions that were in the repair video and put the appliance back together and re=attached the power supply. It worked perfectly. Thanks so much for your service and instruction help.