AGD4370TQ0 Admiral Dryer - Instructions

Once diagnosed, repair was fairly simple. Shut off gas and electric first of course... had to remove the front panel to access valve assembly. removed 3 screws that hold valve assy to floor as well as 1 screw that attaches valve exhaust to the burner assy. reposition new valve assy and reverse the process. was done in about 20 minutes. The wife is once again a happy woman!!

Can't stop laughing about the mistake I almost made, before I even looked on internet I called Sears and scheduled a repair appointment, $80.00 just to have someone come out and tell me what my problem was not to repair it but to tell me whats wrong. And I told them the belt had broken I heard it when it snapped. Long story short version I found your website and entered appliance information, found part for $15.00 but also found on-site video clearly making the needed repair. Clear step by step instructions taking only 8 minutes looked very easy so I took a chance ordered the part two days later part arrived so I went into basement armed with laptop and tools. MAN it was easy.... too easy ....worked out fine video was spot on. Thanks you guys are a great company

removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.

Remove two screws from lint trap lift top, disconnet wires on front panel. Remove front panel and drum take out two screw from coilvalve remove and replace with new valves.

Had no definative directions so kind of had to play it by ear. once I got the top and front off the directions that came with the part were spot on. My biggest problem was I guess I was a little over agressive with the drum and I pulled the tension pulley off the bottom. I had to drill a hole and bolt it back down because I couldnt get the little flanges to bend over enough to hold it. It works now but I havent done a load of clothes yet to make sure it will stay together

My husband and I followed the video step by step and it worked like a charm.

My Whirlpool washer/dryer combo is 15 years old and has given trouble-free service until this belt snapped. I went to the PartSelect website for the replacement part and found the instructional video. As a DIY neophyte I know my limits but this looked like something I could tackle and save a few bucks on. The part arrived pronto and installation went smooth as butta! I couldn't be happier and even the wife is impressed. Knowing what a service call would have cost makes the whole shebang even sweeter. Thank you PartSelect!

after the removal of the front i removed the drum and inspect all idler wheels for ware replace if needed. if not clean and lube. idlers must be in good condition...bad idler wheels can cause the belt to brake

Pulled the front of the dryer off. Removed the old belt. Replaced the new one by threading it flat side down, except for the drive motor which was ribbed, so the belt had to be installed sort of serpentine like. Replaced front of dryer and it's like new.

Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!

The very first thing you want to do is Unplug the Dryer. I then took the two screws out that hold the lint screen to the top of the dryer. Then I used and old butter knife to pry the front top of the machine open. The top is held in place by two plastic clamps. Once I got the top loose I raise it up. Once I had it raised, I pulled up and out on the front panel where the dryer door is. I left the door switch connected and just put the panel off to the right. I then removed the old belt which was lying under the drum. The drum does drop slightly once you take the door off. This was one of the hardest part of the project for me as I did not have any help. This would be much easier if you just have one other person to hold the drum. Anyway, I then placed the new belt around the drum and used my left shoulder / arm to hold up the drum while feeding the belt in the slot on the tensioner and then over the dryer motor pulley. Make sure you don't twist the belt. I originally had a twist and when I hand turned the drum the belt came off the pulley and the tensioner. I had to rethread the belt through the slot on the pulley and then put the belt back on the dryer motor pulley. I then gave the drum a couple complete turns to make sure everything was staying in place. The tensioner on my dryer did not look like the instructions that came with the new belt. My belt tensioner is like a half circle and the belt just rides on it. I think if I had it to do over I would have purchased a new tensioner also. I feel that the belts constant motion against the tensioner probably causes it to wear out faster. Once I made sure evrything was staying on I replaced the front panel that has the door. You just slide the bottom into the slots while holding up on the drum so it lies on the felt padding around the door. Replace all screws and presto. Works like a new Dryer. Make sure you don't forget to plug it back in... Overall it's a pretty easy fix and much less expensive then a service call or purchasing a new Dryer.

I ordered the thermostat switch thinking I'd isolated the problem. Discovering that wasn't the problem, I disconnected and inspected the heater coils and found the break in the coil. I then ordered the heater element (also from Partselect.com). It was simple, fast and works like a champ. I did discover my outside vent had a bird's nest in it. You really need to occasionally check your dryer vent (inside and out), for lint and apparently bird's nests.

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

Maytag makes it really easy to replace this part. Unlike the video which has the access panel in the rear of the dryer, Maytag accesses all the thermostats and wiring front the front so you don't even have to pull the unit away from the wall. Smart!! The video was great to show you what the part looks like and how its installed. Installed the part in less than 10 minutes. Now our clothes are drying as they should in half the time...best $20 I spent in a while.

Pushed in the Door Catch, and it was fixed.