Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AGD4370TQ0 Maytag

AGD4370TQ0 Admiral Dryer - Overview

Get Parts and Repair Help for AGD4370TQ0

If you know the dryer repair part you need, you can browse the list of all parts on the AGD4370TQ0, or you can search by name or part description. You can also find your part by where it is located on the AGD4370TQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for AGD4370TQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$9.72

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$15.16

Thermostat, Internal-Bias

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.

$15.40

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you ...

$18.19

Igniter Kit

This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is used for many gas clothes dryers.

$7.57

Tri Ring

Sold individually.

$5.15

Leveling Foot

Sold individually.

$29.50

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.This flame sensor is three inches long and is used for many gas clothes dryers.This flame sensor assembly is made...

$16.61

Door Switch Assembly

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

$16.02

Switch, Push-To-Start

This part starts the drying or washing operation.

$9.56

Light Bulb - 10W

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer ran but would not heat

  • Customer: Gary from Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 289 of 325 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Timer wasn't working (New Timer)

  • Customer: Joaquin from Las Vegas, NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 124 of 70 people found this instruction helpful
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I ordered the coils for ... read more

Dryer would stay on after opening the Door. The switch that turns off the dryer when you open the door was not broken.

  • Customer: John from Bethesda, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 115 of 121 people found this instruction helpful
You open up the lint filter access door and remove the two small screws that hold it to the top of the dryer. Once they are removed, you insert a flat blade screwdriver under front-top of the unit and the top will pop off. Exerting a little pressure towards you will help lift to top off the mounts. There are no other screws to remove.
The new switch... read more