Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven pilot light glowed but would not light.
Sadly, we had order the whole burner assembly , when it was just the thermocouple that was burn up. Pull oven away from wall, access burner assembly, take panel off behind control knobs (4 screws)to expose thermocouple. Install new copper line (thermocouple is attached) in same place where old line comes out. This was kind of tricky , you have to fish it through the insulation. One half goes down to oven burner and one goes to top of oven for stove top burner. Once in place, screw nut down on both ends to hold in place. Put it all back together. No need to replace burner unit if that was not the problem. Now you have a spare.
My old burners were beyond the point of coming clean and made my stove top look bad.
My husband and I simply took the burner units out of the packing, took the old ones off, put the new ones in. The new units needed to be leveled, but the leveling nuts included fit perfectly, and the entire repair took less than 15 minutes.
two of the burners were not working at all, the other two were blackening pots and pans
I turned off the gas flow to the appliance, removed the old oriface spuds with the adjustable wrench, inserted the new oriface spuds and tightened them with the adjustable wrench. The double burner assembly just dropped on. They fit perfectly. I did not have to use the leveling nuts that were included with the burners. The old levelers were still in place and set perfectly for the new burners. Very easy repair, and the range works like a new one.
my husband who is very handy took it a part, replaced the glass and put it back together - he did remove the door from the oven first and put it on the counter to work on it. I had the schematic picture of the door ready in case he needed it. He didn't really.
Burners were burning the pans and flames coming out at all different angles of the burner
The toughest part of the repair was the preparation to remove the old burners. As a result of the burning there was a carbon residue on the burners, on the gas outlet feed to the burners. This took some scrubbing and removing the carbon residue. Bits had burned onto the outlet and had to be scrapped off. Once all cleaned, replacing the burners was easy just had to place the balancing nuts in place and put on the burners. One problem arose the hood of the stove did not go back in place after replacing the burners so I then removed the balancing nuts put back on the burners stove top hood fit back in place and burners operated properly. This part of the repair took five minutes.
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
I was surprised to find that the 2 screws holding on the plastic end caps were not philips. it looked like an allen wrench deal but that didn't work. Turned out that I had to buy a hex tool. Looked kinda like a swiss army knife but had allen wrench like hex tools in various sizes. By then I was determined to finish the job even if it meant buying a tool I'd never use again. The job took about five minutes once I had the right tool. The stove looks normal now. The stove looks brand new but for some reason there were cracks in the end caps where the screw hole were.
Dissassembled top of stove, removed porcelain top. unhooked pilot sensing line from oven thermostat. Removed bottom slide out drawer to gain access to pilot and burner assembly. Removed pilot thermocouple and burner assembly. Pulled down old pilot sensing line through insulation @ back of stove. Shoved new pilot sensing line up into insulation @ back of stove. Used long hook to pull line up through insulation. Installed new pilot thermocouple burner assy in bottom. Hooked up new sensing line to oven thermostat.Reassembled top components, lit pilots and tested operation.
I needed another oven rack. It came with two. Now I have three.
I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.
ordered parts, 2 double burners, 3 days later they arrived.opened box. lift stove top, lift out old burner,placed next to new burner to see if they were the same. THEY WERE. place in new burner, checked to see if burner assembly fit correctly. IT DID. units purchased were exact replacements. supplied spacer nuts not needed. easy fix looks new again, thanks.