Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AFF2534FEW > Instructions

AFF2534FEW Amana Refrigerator - Instructions

All installation instructions for AFF2534FEW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AFF2534FEW
781-795 of 870
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken because parts are made of plastic

  • Customer: Gordon from Elgin, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pretty simple. Just lift out old parts and put new ones in

The ice maker was corroded and didn't make ice.

  • Customer: Debra from Chippewa Falls, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Getting the old ice maker out was not difficult - it sits on a small ridge built into the freezer and then it takes three screws to attach it to the side of the refrigerator. Three important things to remember: (1) take off the metal bar that shuts off the ice maker from the old part, the new part doesn't come with the bar; (2) keep the screws and the cap from the old ice maker as they don't come with the replacement part either; and (3) make sure you put the water tube back into the holder otherwise it will pour all over the freezer (and not into the ice tray).

Refrigerator door not closing automatically.

  • Customer: David from Southport, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced door closer part on hinge. Did not fix problem. Be sure to order mating bushing that goes in the bottom of the door . Part #67004977

broken fan blade

  • Customer: David from Ceres, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug refrigerator, take backing off with nut driver. Pull old blade off and put new blade on. Put backing back on and plug in.

Switch was not working after a repairman had fixed something else

  • Customer: Jackie from Nova, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Broken lower drawer lid hinge

  • Customer: Chris from Amherst, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed drawers from fridge, removed screws/bolts from end cap, removed end cap with busted hinge pin,installed new end cap with lid , replaced drawers

not making ice

  • Customer: charles from lima, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

Fridge section too warm and freezer cold

  • Customer: Sheila from Folsom, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The unit has two fans on it. One is located in the back and the other is locate inside the freezer section behind the panel. Remove the four bolts holding the door to the sliding rack. Remove the ice machine. Remove the back panel. Noticed that the fan was covered in ice thus shorting the fan motor. Tested for voltage to the fan was good. Replaced evaporator fan motor and unit works perfectly

The tab that holds the lid over the bottom deli door broke off and the lid would not stay in place

  • Customer: Frank from Pomona Park, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the bottom drawer, the two upper drawers and the glass that covered the lower drawer. Took three screws out of the left side pantry end cap and replaced it with the new part. New end cap in place, put the drawers back in, put the cover back on and it works like a charm.

Pantry cover hinge broke

  • Customer: Daniel from Caldwell, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Repair was helped by reading what others shared with similar issue helped a lot. First remove all bins and glass pane. Use the nut driver to remove three screws that hold the pantry. Be careful while removing it from refrigerator. There a an vent control that clips onto back side of refrigerator and attaches to pantry end cap. Remove this piece, be careful as not to break it. This piece ( the guts) attaches to the slide piece that attaches to the controller, remove carefully by turning it to align the slot tab. Then remove the pantry sliders by two screws by using your nut driver. Reverse these steps for reinstall. Then place completed unit into refrigerator, by clipping the back vent control, don't forget the square foam gasket. Then slide the pantry end cap into place, pay attention to the front of the end cap as you may need to slide into the clip to lock in place. Then screw in the three screws, careful not to tighten to much, as it might crack.

lower gasket cover torn

  • Customer: Keith from Jackson, AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
TAKE NOTE HOW OLD GASKET IS ORIENTED!!!old gasket can be removed by starting to pull out at top left hand corner, there is just enough space behind hinged door flap to put a finger behind the gasket and moving down and behind the flap remove gasket from it's slot, once you reach the bottom of the door the rest of the gasket is very easily removed. If new gasket is deformed in shipping, use a hair dryer to help staighten. Loop new gasket over shelf inside door. start at top left corner and continue inserting gasket into it's slot all the way round.

Ice maker pouring water into icebucket

  • Customer: Grant from Cary, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watching the video made this dead easy. If I had a newer refrigerator, I suspect it would have taken 10 minutes. Since I have an older 'fridge, I ran into two issues not in the PartSelect video. First - there were no "clips" to slip the icemaker into/out of, the unit was screwed directly into the freezer wall. Kinda hard to see the screws, especially the one in front, but not a big problem. Second - there is a wire-harness clip at the back side of the icemaker, that hooks onto the ledge of the back connector, just under the screw. That clip had slipped, and until I figured that out and reseated it, it made getting to the rear screw wit the nutdriver a serious pain. Other than those two issues, though, the job was exactly as easy as the video makes it look!

Water leaking into bin

  • Customer: Charles from Fort Myers, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Cubes in bin were freezing together due to water leaking from the ice maker assembly. Replacement went easy with bin rails removed.

ice maker leaking the covering was coming off the tray

  • Customer: Curtis from Frisco, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1. removed bottom screw. 2. pinched sides of rear connection to disconnected ice maker (noted red wire on top in cabinet rear). 3. bump out old unit taping to release tab on bottom. 4. disconnect wire from icemaker and remove wire holder with philips screwdriver.ew ice maker. 4. reattach harness to new ice make and replace clip. 6 reattach l bracket to bottom of ice maker. 7. detach shut off wire from old ice maker and replace on the new maker. 8. place back into position in freezer compartment. 9. reattach water delivery tube 10. connect wire to rear of cabinet. If motor drive still good on old maker scavenge before throwing away bad parts.

the left side pivot broke off

  • Customer: John from New Market, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the lower shelves and then the left hand mount, 2 screws. Installed the new part, replaced the cover and the shelves.... done. very easy to do. the parts arrived ricki tic
All Instructions for the AFF2534FEW
781-795 of 870