Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AFD2535DEB > Instructions

AFD2535DEB Amana Refrigerator - Instructions

All installation instructions for AFD2535DEB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AFD2535DEB
961-975 of 1,041
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker leaking water and creating ice jams in freezer

  • Customer: David from Houston, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced icemaker by using total kit. Watched youtube video put on by partselect folks. Very easy to follow.

The center rail that holds the two drawers broke

  • Customer: Connie from Middletown, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took out the drawers, cleaned off the shelf above then took the glass shelf out of the fridge. The broken piece just lifted out and I snapped the new one in and replaced everything! All better!

The center rail that holds the vegetable bins had broken.

  • Customer: Ted from Cedar Park, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After reading others who did this same repair, I removed the bins and emptied the bottom shelf. Now came the hard part as the glass had not been removed in a long while. It was stuck on with gunk. I removed the top glass and the lower glass by putting hand pressure from underneath and cleaned them. This took the longest time. With the bottom glass in and the top glass out, I snapped in the new piece, the actual repair took about 5 minutes including putting the drawers back in and testing them.

Ice maker leaking water dripping into the bin and freezing the dispensing unit

  • Customer: Richard from Port Orange, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I checked the part number and an exact replacement was ordered. The old unit was removed and what I failed to note was that the water supply hose for the new unit entered from the side. Further examination showed a small "break-out" piece at the rear of the unit. but I still had to do something about the hole in the side. I used a piece of metal tape to close off that hole, trimmed it to size, and installed the unit. It was really an easy install after I figured out what to do about the hole. Evidently, this unit is mounted on the side of the freezer compartment in some models. Reading the reports of others was a big help.

The piece that holds the shelf trim in place was not molded like the other side.

  • Customer: David from San Juan Capistrano, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I put a stainless steel screw into the pantry end cap to hold the shelf trim in place so my pantry drawer would operate.

Refrigerator and freezer stopped cooling. Compressor pump not coming on

  • Customer: Joseph from North Anddover, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the cover panel. There is a clip that holds the relay and capacitor to the pump. Use a screwdriver to pry it off. Unplug the relay. The capacitor is plugged into the relay and they come together which was a surprise, I thought I only ordered the relay. Unplug a cable from the relay. Insert that cable into the new relay and plug it into the compressor. Reattach the clip. One be important instruction. Unplug the refrigerator for at least 8 hours before installation to allow the compressor to cool down. I tried first without allowing the compressor to cool and it did not work. After letting it cool I tried again and it worked like charm. Make sure the refrigerator is unplugged when doing the repair

Old ice maker worked irratically and finally quit for good.

  • Customer: Richard from Peoria, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video and advice from the many others on this site and only have a few additional comments. First, the decorative cover on the front of the old unit is held on with two plastic teeth on the top and bottom of the cover. This was not at all apparent and it took me awhile to figure it out. I used a sharp knife to pry up the top edge until the teeth lost their grip on the metal notches in the old unit. Second, don't try to pull the cables out of the front of the old unit before removing that cover. It is held in with a plastic snap that must be depressed after the cover is removed. The video does a good job explaining how to remove the old metal arm and attach it to the new unit so that it will recognize the ice level in the bucket. Finally, don't bother looking around the web site for a button that enables you to add to these comments. You'll be contacted by email in a week or two for that.

Freezer freezing up in back and frig getting warm

  • Customer: Heidi from Etters, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!

Switch didn't work

  • Customer: Don from Laramie, WY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

ice maker quit making ice

  • Customer: denton from grinnell, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged the refrigerator.Removed the nut on the front bottom side from the support bracket with a nut driver.Pull down and out the old icemaker but not clear out to remove the electrical connector reaching to the back . Re-used the old front cover and the wire support clips and the wire connector assembly.Also put the shut off wire on the new icemaker.Re-installed in reverse sequence and waited for ice cubes to be made.Make sure the water line coming in the back goes to the ice tray.

Ice maker had been leaking for several months and needed replaced

  • Customer: Joe from Leonard, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took the old part out and put the new one in and it works like it should. I loosened two screws and took one screw out with nutdriver. then I used the old wiring harness, bail and cover to finish.

I replaced the end panel where a plastic hinge pin had broken

  • Customer: Stephen L. from North Palm Beach, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove the shelves and the other trays. Use the nutdriver to extract the screws and the panel. Pay attention to the orientation of plastic parts when replacing plastic slides to avoid breaking the plastic slide components. Avoiding too much stress on plastic parts is important.

The ice maker had been dripping and than stopped making ice. I worked with it and got it to work again for a few days and than the same problem occured.

  • Customer: Kathleen from Waller, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on line first. I shut off the power to the refreigerator. I took the one screw out on the bottom of the ice-maker and pushed up on the ice maker. Than I disconnected the power harness inside the refrigerator. I took it out and changed out the harness from the old one to the new one and also the bar that dumps the ice. I reconnectected the harness to the back of the refrigerator, made sure that the water spout lined up correctly. Pushed the ice maker down on the screws and reconnected the screw that I had removed. Waited about 1 hour and had ice cubes. This was an easy process after watching the video.

Tab on the end cap broke off

  • Customer: Bernard from Ashburn, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove the pantry drawer door, then remove the pantry drawer. Remove the 2 vegetable bins to gain rom to see and to ease access. Remove the 2 screws holding the end cap to the interior of the box. remove the slide from the end cap and place it on the new one. Reinstall the end cap being sure to have the tabs go into the slots at the back. Make sure the end cap also mates with the tab in the front, Reinstall the drawer and the bins and the pantry door.

The hinge pin broke that holds the door on the full-width vegetable drawer

  • Customer: Leonard from Lexington, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed all drawers (including the two above the repair site, removed the left side end cap - it was help in place with only two screws (one screw hole appears never to have had a screw). Swapped out the broken part for the new one, reinstalled the screws, put the drawers back, mounted the operable door to the two hinge pins, and things were fixed.
All Instructions for the AFD2535DEB
961-975 of 1,041