Models > AFD2535DEB > Instructions

AFD2535DEB Amana Refrigerator - Instructions

All installation instructions for AFD2535DEB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AFD2535DEB
901-915 of 1,041
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The right hing pin borke off approximatrely 1 week after getting unit home.

  • Customer: Gary from Carthage TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the upper crisper drawers. I then removed the bottom crisper drawer. I then removed plate glass covering that covered the bottom crisper drawer. I removed the plate glass frame in order to be able to get to the 3 screws holding right hand rail. I removed the 3 screws with nut driver to remove rail. I detached the humidity control linkage and linkage cover from right hand rail. I reinstall every thing in reverse of how I had just taken things apart when installing new right hand rail. There was a lot of good information on how to replace rails that came with rail order. also there was a lot of good information on iste where part was ordered from. THANKS

The tab that holds the door broke off and had to replace the entire right piece that held the door

  • Customer: Donna from West Springfield MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I did not do the repair my husband did but it only took him 20 minutes and it was done. I am especially thrilled with the fact that the part came the very next day without paying for extra postage. Thank you for your quick response. In fact I ordered a filter for the same fridge the same day from a different parts place and it still has not arrived and its been more than 10 days. Guess who gets my business in the future for appliance repairs.

Replace Right Pantry End Cap

  • Customer: Barry from Marianna PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Parts arrived in less than 2 days. Installation was easy. The only tricky part was removing the Temperature/Humidity control from the old part. A little "bending" of the plastic is necessary to remove the slide mechanism. After that, it was quite easy.

brokenpivot arm

  • Customer: Will from Missoula MT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
used the directions from PartSelect

Parts were broken

  • Customer: heby from Whittier CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pretty easy, just a screw driver and replacing the parts. We were surprised on how easy it was.

Broken Pantry Lid Cover Hinge

  • Customer: David from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
It was easy, since I took the old one out, I knew what to do to put the new one in. Not problem, just a couple of screws!

hinge tip pantry end cap-right side broken off

  • Customer: Fred from Greenville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
easy as pie!!!!!!!!!!

I replaced the end panel where a plastic hinge pin had broken

  • Customer: Stephen L. from North Palm Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove the shelves and the other trays. Use the nutdriver to extract the screws and the panel. Pay attention to the orientation of plastic parts when replacing plastic slides to avoid breaking the plastic slide components. Avoiding too much stress on plastic parts is important.

Pantry end cap tab broke off. Right side. Left side broke last year. Very poor design.

  • Customer: Candace from Albuquerque NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed veggie draws and glass tray.

Tab for pantry draw door snapped off

  • Customer: Robert from Camden Wyoming DE
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
For the filter.....lefty loosey righty tighty...just that easy. For the right side pantry end cap.....removed the pantry,veggie and fruit draws..lifted out the glass shelve with it's end guides... Two screws to remove the track. another 3 screws to removes the end cap....pulled the temp control attached to the rear out with the cap. Disconnect the temp control lever .......reverse the process and your home free.

broke the tab on the right side, for the second time.....

  • Customer: paul from westminstrer MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the fruit and veggie drawers & the deli (pantry) drawer. (Tim from Littleton CO helped me in this when he described his experience)......what helped me this time is before I put the side panel all the way into its' home position, I fastened the deli lid in place, being sure to not put any strain on the tab that I broke the last time. This go around I ordered two of these side panels just in case. I received my parts in two days. thanks!!!

Broken head that holds pantry lid in place

  • Customer: Susan from Salem OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed pantry drawer ,glass top, and the 2 crisper drawers. Removed 3 screws , removed broken one. Removed temperature slide and placed it on to new one. Screwed new one in! Easy Peasy!

hinge pin broke off of right end cap

  • Customer: william from towson MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
remove drawers , shelf, and end cap. be careful to look at crisper control mechinism. 2 screws attach end cap to refrigerator.remove all atachments from old end cap and re install on new end cap.re install into refrigerator.

The right side pantry end cap broke

  • Customer: Jolene from Kingwood TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My husband removed the crisper storage drawers and the shelf then removed the pantry drawer. The broken end cap was very easy to remove, just remove two screws and the new one was installed. Simple and my husband really enjoyed saving $2400! That was what a new one would have cost if he could not have replaced the part!

The little part that fits into the hole of the deli tray door broke apart from the panel on the right side of the refrigerator.

  • Customer: Miranda from Kansas City MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
There are two screws that holds the panel on. I took the screws out pulled the panel and attachments out. Removed the attachments from the old panel put them on the new panel. It was really easy to figure out how to fit the pieces back together. Screwed the panel and attachments back into to place and perfect. I Put the door back on the deli tray. No readjusting was necessary at all good as new fits great no problems. You pull the tray out the door flips up every thing works fine.
All Instructions for the AFD2535DEB
901-915 of 1,041