Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Front 8" burner stuck on high no matter where dial was set.
This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.
It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole. TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.
Pull out the range...hardest part. Remove back panel. Remove/install switch PS, This is second switch I had to replace. Try making them in the United States.
The bake element in this oven is covered by a tray but after locating the screws for that and removing I could see the element was burnt so I just removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) then just reversed the procedure to install. Don't forget to unplug the unit first.
Found serial # as advised on web site. Found parts listing & ordered part. Got it in less than a week . Unfastened two screws on top of door. Inserted glass. Applied a little mastic to prevent it from coming out again. Done & done. Do I get a prize ?
lower baking element was fried and no longer worked
Turn of power to the range. The element lies beneath a metal cover. The cover is held down by two screws in each of the back cornors. The burner element is held by a screw in the the back and by two screws near the front. Replacing the element was a snap. With the screws removed, pull on the element until the connecting wires are exposed. Pull the wires from the element and attatch to new element. Replace screws, cover etc. Turn on power and note the time it takes to reach a preset temp. You may detect a slight oder form a coating on the new element. .
First I removed the oven door, then I removed the three screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I connected the two wires to the new element , replaced the three holding screws and the oven door. ------END-------
First of all, let me say how "Not Handy" I am when it comes to these things. I decided to give this part a try after my oven decided to fail on Thanksgiving Day, so I ordered the part. It arrived on time as promised and packaged very well. The on-line parts breakout and testimony from the other buyers were so helpful. I had our oven back up and running in less than 10 minutes.
One thing I would also recommend is that you burn the element once installed for at least 15 minutes to get the newness smell off of it and then it won't permeate your food items.
Thanks, Parts Select! You saved me over $900.00; the price it was going to cost me to buy a new oven. :)
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
removed the two screws in the rear of the oven to access the element. once exposed I removed the four screws holding the element in place. Went to the ouitside back of the stove and removed one screw holding the shield to access the terminals for the element. Installation was in reverse order.
