Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Soap Dispenser Door Would Not Open
First, I searched the repair help on this site to see what others did to repair their diswashers, and it looked easy, so I just followed the same instructions. First, I used a hex star key wrench to remove the screws that hold in the interior door cover. I disconnected the leads to the defective wax motor, reconnected the leads to the new motor and screwed the door back together. It took 15-20 minutes and was a piece of cake! My first appliance repair, and as a single woman and first-time homeowner, I was really impressed with this site! It gave me confidence to tackle more home repairs instead of calling for service and getting raked over the coals.
First unplug the unit. Open door. Take a special tool to remove all the screws (star shaped) around the edge of the door, and remove plastic panel where motor for detergent cup sits. Remove wires (two) from the motor. Remove wax motor by unsnapping motor from its cradle--comes out by moving the fingers holding it in. Push new motor into position, being sure the round pin sticking out at the end (on the left side) so that it sits in the groove made for it. Replace panel and screws, plug power cable back into its box. Close detergent cup door, turm on dishwasher, run through cycle, open door and check to see if detergent door opened up. If it did, then fill with dishes and wash.
Ordered the spring and the Door Spring Linkage. Turned out to be a broken Door Spring Linkage not the spring. Unscrewed the two screws securing the dishwasher to the countertop and slightly pulled out the dishwasher enough to see the spring. Replaced the broken Door spring linkage and it resolved the issue.
Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.
No Water caused soap to not dispense & no clean dishes.
I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.
turn off breaker turn off water supply line note wire color locations on notepad disconnect 2 spade lugs (pliers) disconnect inlet line (adj. wrench) disconnect outlet line (pliers on hose clamp) remove old valve assembly (4 screws w/nutdriver) remove ground jumper from old valve remove inlet pipe ell from old unit (vise & pliers) clean open end of pipe ell (file) apply teflon dope tape to pipe threads install pipe ell on new valve reorient solenoid 90degrees cw to match Maytag installation reinstall ground jumper install new valve assembly in dishwasher reconnect hose and hose clamp reconnect inlet line reconnect spade lugs turn on supply line, check for leaks turn on breaker start washer at appropriate cycle to test water flow done!
1) Emptied Dishwasher (roll-around model) 2) Tipped it onto its back 3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver) 4) Opened Door to access side panel (careful not to let it drop on my fingers) 5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring. 6) Removed broken link 7) Installed new link and spring noting the spring direction from the spring on the other side of the door. 8) Pulled spring over the bottom rail bracket with pliers. 9) Reinstalled panels in the reverse order.
First, I removed the screws that hold the interior part of the door in place. Next, I removed the two screws that covers the interior parts of the latch release in place. Then, I removed the broken latch, put in the new one and attached the spring. I put the pieces back in place, and the two screws back in. Finally, I screwed the door panel back together.
removed the agitator,and a couple of baskets til i was able to gain access to the pump impeller & pump housing. i replace those parts,put back together,all works great now
I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems. I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in. No more leaks!
I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.
Unscrewed the inside door panel. Removed the reservoir assembly. Disconnected the wax motor. Replaced it with the new motor. Replaced the new o-ring. Done. The hardest part was finding out why it was not working and how to fix it. Google for a long time in order to find some idea what to do. Then took the door apart to see the reservoir and the wax motor. After that, it was pretty easy. HTH
Dishwasher started to make a grinding noise and was very loud
I disconnected the dishwasher and started to take the impeller assembly apart but could not get it all apart. Went on line to start looking for the parts and came to Partselect and they had and exploded view of the the whole inside assembly and I saw what was wroung, some parts had broken and melted together. With this picture I was able to see what had happened and able to get it all apart. Ordered the bad parts, got them within a week (this was over the hoildays), took about 15 minutes to get the new parts in and the dishwasher running. It runs great now, very quiet, it's like a new dishwasher for $30. P.S. I had to order some extra parts because one of my dogs was helping me and chew them up.