ADG20L4W Admiral Dryer - Instructions

Watch the video on your site and it is very helpful and that is only I needed.

After watching the repair video that was linked in the part delivery confirmation email, the repair went really easy. I just used the putty knife to pop the lid, then removed two sheet metal screws holding the front panel with the nut driver. I disconnected the two wires from the door switch. The front panel slid right up and out. The old belt was broken and lying at the bottom of the dryer. I ran the new belt around the drum, and around the tensioner and drive pulley. This was not as difficult as I imagined it would be. I spun the drum one revolution to make sure the belt was riding right. Before I put the front panel back on I took the opportunity to clean the lint out of the blower. I then just reversed the front panel removal process and snapped the lid back down. This repair took maybe 10 minutes. If I had to do it again I could probably do it in 5. It's just that easy. The dryer works perfectly now.

Looked up on-line for tips, found computer animated video. It was easy as it looked, took longer to take dryer apart (not long). Other note on problem; neighbor who works on washer/dryers said that the motor was probably going. replaced belt anyway because I already purchased it before we spoken. Throwing caution to the wind!!

I watched the online video three times. This was extremely useful. I just did what it showed. I doubt I could have fixed it without the video. This has got to be the best feature of the internet. I didn't have the exact model number, but the belt fit. I was surprised at how close the tensioning wheel was to the motor. Perhaps the belt will stretch with age and use.

Un plug dryer . Take off dryer door . Remove front panel by pulling out. Remove 2 screws holding coil bracket . Remove electrical connectors ,remove 2 coils . Install 2 new coils same as old ones connect elect. Wires replace coil holding bkt. Unplug flame sensor . Remove 1 screw . Replace old flame sensor with new plugin elect. Connector replace in reverse wala ,,,alldone button up dryer plug in dryer . . Good to go.

We noticed the drum wasn't spinning, but the heat was turning on. About 3 years ago the heat was broken and it turned out that there was a little thermal fuse in there that needed swapped out, that was easy too fix too. Anyway, I looked up on youtube how to change out dryer belts on maytag units and it looked pretty straight forward. The model they showed was easier to access than my model, but I was able to still figure it out. Just pop off the top panel (they used a putty knife at the two clip points on the front, but I just yanked it up with a little force and it popped right up). Then unscrew the two little screws holding the front panel on, then pull off the front panel completely. This exposes the drum. The example on youtube showed easy front access to the belt assembly, but in my model, there was a stand for the drum as well as the drum motor in the way. So I just pulled the whole drum out the front most of the way, then I went behind the drum where I had exposed the pully/motor shaft assembly and then fed in the new belt into belt tension assembly that connects to the motor. While keeping it taught so the ribs of the belt would stay on the motor head (I had my wife hold it taught) I pushed the drum back toward the hanging belt and then worked the edges of the belt around the drum until it once again was completely around the drum. Then I slowly pushed the drum all the way back into place while continually working the belt back into place as I went. I then manually rolled the drum around a few times to ensure it was rolling correctly and that the belt was indeed in the right place. After a few good spins without it changing position, I reassembled the unit. It was very painless and took about 15-20 minutes in all. Works just fine again.

I replaced belt by myself. Took dryer apart,laid dryer on its back, put belt and pulley on. Rotated drum to make sure seal was in place. Cleaned out machine while I had it apart.

My husband and I followed the video step by step and it worked like a charm.

My Whirlpool washer/dryer combo is 15 years old and has given trouble-free service until this belt snapped. I went to the PartSelect website for the replacement part and found the instructional video. As a DIY neophyte I know my limits but this looked like something I could tackle and save a few bucks on. The part arrived pronto and installation went smooth as butta! I couldn't be happier and even the wife is impressed. Knowing what a service call would have cost makes the whole shebang even sweeter. Thank you PartSelect!

after the removal of the front i removed the drum and inspect all idler wheels for ware replace if needed. if not clean and lube. idlers must be in good condition...bad idler wheels can cause the belt to brake

Pulled the front of the dryer off. Removed the old belt. Replaced the new one by threading it flat side down, except for the drive motor which was ribbed, so the belt had to be installed sort of serpentine like. Replaced front of dryer and it's like new.

Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!

The very first thing you want to do is Unplug the Dryer. I then took the two screws out that hold the lint screen to the top of the dryer. Then I used and old butter knife to pry the front top of the machine open. The top is held in place by two plastic clamps. Once I got the top loose I raise it up. Once I had it raised, I pulled up and out on the front panel where the dryer door is. I left the door switch connected and just put the panel off to the right. I then removed the old belt which was lying under the drum. The drum does drop slightly once you take the door off. This was one of the hardest part of the project for me as I did not have any help. This would be much easier if you just have one other person to hold the drum. Anyway, I then placed the new belt around the drum and used my left shoulder / arm to hold up the drum while feeding the belt in the slot on the tensioner and then over the dryer motor pulley. Make sure you don't twist the belt. I originally had a twist and when I hand turned the drum the belt came off the pulley and the tensioner. I had to rethread the belt through the slot on the pulley and then put the belt back on the dryer motor pulley. I then gave the drum a couple complete turns to make sure everything was staying in place. The tensioner on my dryer did not look like the instructions that came with the new belt. My belt tensioner is like a half circle and the belt just rides on it. I think if I had it to do over I would have purchased a new tensioner also. I feel that the belts constant motion against the tensioner probably causes it to wear out faster. Once I made sure evrything was staying on I replaced the front panel that has the door. You just slide the bottom into the slots while holding up on the drum so it lies on the felt padding around the door. Replace all screws and presto. Works like a new Dryer. Make sure you don't forget to plug it back in... Overall it's a pretty easy fix and much less expensive then a service call or purchasing a new Dryer.

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

Pushed in the Door Catch, and it was fixed.