Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ADG20L1H > Parts

ADG20L1H Admiral Dryer - Parts

All parts for the Admiral Dryer ADG20L1H

Below is a list of all parts for the Admiral Dryer ADG20L1H - Residential. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the ADG20L1H
1-14 of 96
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$21.99

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils ...

$15.68

High Limit Kit

The high limit kit comes with three separate thermal fuses for dryers. One electric thermal fuse with a limit of 258, one gas high limit at 240, and one gas and electric high limit thermostat with a limit at 300. The thermal fuse kit shuts off the motor in the dryer when it begins to overheat. If the dryer will not heat, is overheated, shuts off too soon, or takes too long to dry then the thermal fuse might have exploded and need to be replaced. For replacement instructions refer to the diagram by manufacturer. For safety, unplug the dryer before installing the part.

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...

$50.03

Rear Drum Support Roller Kit

The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four screws, one spacer, two washers, two retaining rings, two rear rollers, and two cylinder support shafts. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. Important note: This kit has been updated by the genuine manufacturer to have one spacer that is the thickness of two spacers. Please search by model number to get these parts separately.

$16.18

Rear Drum Support Roller

This rear drum support roller stabilizes the dryer drum and holds it in place during the drying cycle while the drum rotates on the support wheels. If your dryer is making loud squ...

$5.81

Blower Wheel Clamp

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clothes dryer has any of the following symptoms then replacing the clamp can be a solution: making loud noises, not producing enough heat or no heat at all, and/or clothes are taking too long to dry. Make sure to unplug thedryer from power source before installing this part and refer to the installation instructions provided by the manufacturer for further guidance.

$3.02

Screw

This screw is sold individually.

$24.06

Igniter with Wire Harness

This part lights the gas burner to create heat.

$12.05

Drum Glide and Cushion Kit

Pad has adhesive backing.

$5.96

Retaining Ring

This retaining ring is well under an inch long. Made entirely of metal, this ring is intended for use with some clothes dryers.

$29.47

Blower Wheel

This is a beige blower wheel that is made of plastic. Manufactured to fit a 1/'2 inch motor shaft, this blower wheel is 3-1/8 inches deep, and the diameter of the wheel is 7-1/8 in...

$3.02

Screw

This screw is sold individually.

$4.48

Screw

Sold individually.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

All Parts for the ADG20L1H
1-14 of 96