ADE7005AYW Admiral Dryer - Instructions

i took the front off the dryer took belt loose took the tub out the plastic nut on the blower wheel striped out so i took the blower housing apart along with the motor got vise grips on blower wheel replaced motor blower wheel belt and belt tenchinor and spring cleaned all the lint put it back together works fine

Went on line and read it was the Heating Element and maybe the thermostat. It was easy to remove the parts and order new ones. I didn't take the dryer apart, I reinstalled the new parts from the bottom by taking off the face plate. The only problem was getting the screw to stay on the socket it was a one hand operation. I taped the screw to the socket wrench and it work fine. Nothing really hard.

noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!

Ordered new lint filter from part select; paid for it with credit card on line; waited for delivery in one week; received by ups; unboxed; cleaned filter trap area with vacume; and dropped in new filter.

very easy

I had already taken the dryer apart prior to changing the felt seal. Had oiled the rollers, greased the bearings & vacuumed the whole inside of the dryer out. Had used a high temp lubricant on the seal & had stopped squeaking for about a month. I ordered 2 seals & when they arrived, I popped the top of the dryer off using the putty knife to pry the spring latches. I opened the top up & leaned it against a wall. I disconnected the wiring to the light & the switch in the door, making note of the wiring order. Then used a nut driver to take the 2 screws from the inside out, that holds the front cover in place. Then the same for the 4 screws holding the front bulkhead in place. Then lifted up & out from the unit. Then used the putty knife to scrap the adhesive & old seal off the bulkhead. Cleaned as much of the adhesive off, then applied some high temp silicone adhesive to the bulkhead, placed the new seal on, using some clamps to hold it in place. After making sure it had adhered to the seal & bulkhead. Did the reversal of the above mentioned steps. Moved the unit to laundry room, plugged it in then started it & voila no more squeaking dryer.

The repair went better than expected. I watched the video of how to replace the dryer belt and although it wasn't exactly the same, just by watching the video I was able to find my way through the process. Thank you very much for taking the time to create the video, it was very helpful and saved me a bundle of money by being able to do the repair myself.Thanks again!!! Dano, Melbourne Fl.

This is merely taking the old filter out and putting the new filter in. You will not find this part unless you go online or get lucky and find one in a used dryer. It is not necessary but I do recommend vacuuming the inside of the dryer beneath the filter. It is amazing how much lint can be in there.

I removed the top and front of the dryer then the lint filter housing and frame that holds in the drum then the drum belt and drum. Found that tha drive pulley was spining on ths shaft. I removed the fan cover, so I could remove the fan. I disconted wire harnsh and removed motor clamps from back and front of motor. Removed drive pulley and held shaft with a pare of chanellocks. I removed fan with 7/8 socket and impact drill.Then I replaced the motor by taking the motor frame out of the drier for easyer actess. Install fan on new motor by holding drive pulley with cressent while putting on fan with impact drill. Put motor in u shaped saddles making sure they are seated in the bottom. You may have to turn the barring a little. Then reinstale clamps. Put motor back in drier and put drier back togeather. simple saves money 144.00$ for motor and beld no labor. Ed from Mojve CA.

removed bottom kick plate,then door and front drum seal support so i could lift top cover out of the way.took off belt and removed drum to get at support rollers.

I followed the video that you had posted. I don't think I could have done it without the video being posted. Thank you very much.

I followed your online instuctional video. It was a really easy job. The dryer works like the day I bought it. Thanks

Dryer had not been used in over 2 years. After replacing the heater element...it started making very loud screeching noises. Decided to then order all other parts that said could solve noise problem. Felt if I was going to take it apart again, might as well replace everything new. Very helpful video instructions online...took less than 30 mins. the 2nd time. It now runs so smooth, you can't even tell the dryer is running. This website is wonderful!!!!!! The troubleshooting descriptions, parts list, availability of parts, fast delivery, everything is right here to fix anything. If you can't find it....it can't be fixed !!!!!

I followed the instructions on the video fom the website they were clear and precise and I had no idea how easy it would be, thank you... you saved me some $$$ ! It took me close to 2 hours to do the job but it was because I cleaned the dryer and vaccuumed the lint/dust buildup which took some time.

Took the dryer apart through online instruction. Replaced idler lever and belt.