Models > ADE7005AYW > Instructions

ADE7005AYW Admiral Dryer - Instructions

All installation instructions for ADE7005AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ADE7005AYW
391-405 of 424
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken drive belt

  • Customer: chris from bakersfield, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
I was amazed just how easy it was. It would have been much quicker if I had a nut driver instead of a wrench. The video was great. Thank you!

Door catch broken

  • Customer: Martin from Grapevine, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Push new catch in the opening, close the door and VOILA! the door stays closed. Please note that the cost of this part is exorbitant- it's worth about 50 cents but with shipping it cost about $11.00. Check your local hardware store first.

No heat

  • Customer: Nancylee from Boone, IA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off dryer 220V breaker at panel. Remove front kick panel (two 5/16 hex screws at lower corners). Check continuity of high limit thermal fuse with meter; no continuity: fuse blown. Remove two wire clips with pliers. Remove fuse with nut driver (two 1/4 hex screws). Install new fuse. Replace two wires. Replace kick panel with two screws. Reset breaker at panel. Reset, start timer: dryer has heat.

Male door latch would no longer catch.

  • Customer: Joan from North Myrtle Beach, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

When I turned on the dryer it made a squealing/screaching sound.

  • Customer: Robbi from Centennial, AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions provided by Partselect. The video and information were very clear and accurate. I have never taken a dryer apart, but have some tools and the cost savings plus the reward of fixing it myself were enough to inspire me to try. I was so happy with this experience I recently diagnosed and fixed a friends dryer with the helpful information from Partselect.

Sounded like a pair of gym shoes rolling in the dryer

  • Customer: Ronald from Bourbonnais, IL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I recently found your site and was pleasantly pleased with your troubleshooting suggestions and repair videos. My dryer was sounding like there was a pair of gym shoes inside bouncing around and your suggestion of the drum support rollers was right on the money. My dryer cabinet came apart a little differently then what the video showed but was workable.
I would like to suggest sending the washers that go in front of and behind the drum support roller with the drum rollers. The washers on my dryer were completely ground down to powder so I drilled out some stainless steel washers I had in my supply of extra parts. These washers are hard to find in a hardware store due to being so thin.
I would suggest to anyone changing these drum rollers to go ahead and order/replace the drum belt and front guides as long as you have the machine apart and had to take these off to get to drum rollers. I have had my dryer maintenance free for 17 years and figured they were probably close to being worn out as well. My front guides were paper thin and the drum belt had lots of cracks.
Total cost of bringing dryer back up to par was only $45.00. Saved at least $180.00 doing myself.

Dryer Was Not Heating

  • Customer: LANORA from SUMMIT LAKE, WI
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Looked on your wonderful site and found two parts that were listed as 80% the problem. Took a chance and ordered both parts. Husband replaced both parts. And, yeah. . . . . . . . . We had heat. So not sure which one it needed. . . . But, the price of your parts beat the costs of any repair man. Thank you so much. We're drying clothes again!!! Lk

Loud squeal and squeek

  • Customer: Curran from Cadiz, KY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took dryer apart and replaced the drum support rollers. This did not work and problem is still there. The videos at the part select did not help since they seemed to be for a different dryer and nothing in them helped in any way to work on my unit. I did get a repair man out and was told that he had not seen one built like this one before.

No problems encountered.

  • Customer: Michelle from St. Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The only difference is that I took apart the front frame, that is the white plastic plenum. The videos were of a clean machine, mine was not. I decided to wash the plenum so I took it off the frame. Had it not been the middle of winter in St. Louis, I could have hosed it clean outside, but not this winter. Disassembly allowed me to clean the plenum in the sink.I was extremely impressed with the service and videos. I will be doing business with you in the future and am telling all my DIY family and friends.

Broken belt

  • Customer: JOEL from ALTADENA, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I just followed the intructions from the video on the website. That made the replacement easy.

replaced roller wheels/ pulley wheel

  • Customer: david from manlius, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I had two repairs, a few days apart while waiting for diagnosis and parts. I watched the videos and followed the steps, simple as that. I was able to replace the rear roller wheels without taking the drum all the way out. I tried the dryer with this 1st fix, some sounds went away but the worst one remained. Took the drum all the way out and replaced the idler pulley wheel just as the video shows. Everything went back together just fine- no extra parts and the dryer is soooooo quiet. My wife thinks I'm a stud for doing this, thank you partselect.com. A caveat, the e rings that hold the wheels on are a big pain to remove and reapply. The snap ring pliers needed to get these off don't always fit in the little openings to remove the ring.Get the smallest size tips if you buy the pliers. My pliers got an "A" for effort, a "D" for results. I used a pair of slotted screwdrivers to manipulate the rings off. Your mileage may vary.

Dryer making noise

  • Customer: Samuel from Tulsa, OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The problem was easy to troubleshoot using the PartsSelect diagnostics on the website. After viewing the instructional videos for the parts I suspected I placed the order. When the parts arrived I reviewed the videos prior to attempting the repair. The problem was a drum support roller. I began by removing the top and front panels. The model I have was older than the video and the only trouble I had was that the top panel was screwed in place instead of clips. Once that was figured out the repair was pretty easy. I removed the drum, belt and replaced the Drum Support Rollers and Drum Glides, installed a new belt and reassembled. The parts for this type of repair are so reasonable that some of the parts I replaced were to insure longer life but actually were not in bad shape. Overall this was a very cost effective and relatively easy repair.

Dryer squeaking, shutting down, and difficult starting.

  • Customer: Steve from Van Buren, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Motor was replaced with common hand tools, after replacing roller guides and belt.

bushing inside drum support roller disintegrated

  • Customer: R W from Budd Lake, NJ
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair video was very helpful. Until I started, when I discovered that the instructions did not match the design of my dryer. On my dryer, the top panel is secured by two bolts on tabs to the side panels. This puts them behind the front panel, so springing the clips does not help. They are there to hold the front panel to the top panel. Further, the front panel screws lie behind the bottom panel, so that has to come off first. Then the front panel. Then the top panel. All held on by 2 5/16 self-tapping bolts. A useful design feature. Beyond that, everything went according to the video. One other plus, the video plays without requiring the 3rd party software FlashPlayer from Adobe which is not allowed on my computer. So good choice for the video. One further note, at several points it was useful to have a 2nd person to hold parts while I loosened or fastened them, especially to hold the drum while I slipped the belt on the pulley.

Loud sound

  • Customer: Angel R. from Kissimmee, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I knew that it have to be worn out roller drums or the idler pulley with bearing. So, I ordered both items. I watched the repair video to know how to do it. I installed the items and the sound disappeared
All Instructions for the ADE7005AYW
391-405 of 424