ADB3500AWW Amana Dishwasher - Instructions

Simply unscrewed the door and plugged in the new parts. Very quick, very easy, saved us hundreds on a new dishwasher.

The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last considerable longer. I would say this is a typical "defective by design" problem.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

First, I removed the screw, then I took off the old wash arm, then I replaced the wash arm, and replaced the screw. Nothing could be easier!

FIrst I went to your web site; located the part on the easy to read diagram. Next I ordered the part. When the part came to the house (2-3 days), I opened the box and then the packaging, I screwed the part in and Wala! Boom! Bang! She was fixed!

All kidding aside. The part order was quick to locate, quick to ship and one of the easiest companies to deal with. I will return on my next dyi project.

Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

Maytag should be ashamed to put such poor plastic material in an otherwise good design. The seals that join the rotary sprayers to the rear wall had hardened and crumbled away. When I discovered that water pressure had been lost at the spray arms, it was a simple fix. Snap off the failed parts, pay Partselect $37 because Maytag wanted to save a dime and snap in the new parts. (Parts that will fail again in another 3 years.)

Snapped the old part out and snapped the new part in.
It was a piece of cake.

Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

Took the baskets out of the packaging and put them in the dishwasher, took about 15 seconds to put both in. They fit perfect, quality factory parts. Thanks PartSelect!