ADB2500AWS Amana Dishwasher - Instructions

You just remove the old unit and set in the new unit. the wheels were already connected.

I know that I have very hard water, but am reluctant to get a softener. I hope that changing the "guts" of the water delivery to my dishwasher will help...already replaced the filters which helped too... so far, it's a little better.

Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen screws in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms.
Easy...

Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.

1. Removed door inside plastic panel, 2. Removed additional screws holding panel to hinge brackets and control panel, 3. Figured out that this would all have been easier if I'd unhooked door hinge springs first (access from sides), 4. Removed isulation from old panel and reglued to new panel, 5 Reassembled, hooking up door springs last. Voila!

I removed flowplate assembly, chopper assembly, found that the plastic spindle was stripped causing arm not to spin. In the new seal kit, the spindle was made of metal (much better design). I replaced the spindle, chopper, and filter assembly (old one was caked full of gunk). Worked like a charm. A previous post helped me figure out the problem.

Removed the inter door panel replaced broken handle put panel back washed dishes

First I shut off the water and electricity to the dishwasher. I removed the screws holding it in the cabinet and pulled the dishwasher out. Disconnect the water line and turn the unit face down on the floor. I disconnected the wire harness by pulling it out. It was a little hard to pull out. Then I removed the screws holding the pump in place, then removed the pump. I inserted the new pump and replaced the screws, and the wire harness. Then stand the unit upright, reconnect the water line (use teflon tape to prevent water leakage), put the dishwasher back in the cabinet, and restore power and water. Then you're done. It would have been very simple if I had used teflon tape the first time. I had a leak the first time I reconnected the unit and had to take it out again and apply the teflon tape. After that, everything was fine. The dishwasher works great.

Removed the top rack and unscrewed the six screws involved on the rack adjuster. (Take note on how you took the thumb adjuster on top off for easier reassembly) Replace assembly on rack and slide rack back into dish washer. Kudos to PartSelect for getting my part here in less than 24 hours on a normal delivery charge.

PartSelect web-page for this model listed the handle as the most often ordered part. It arrived the next day after the order. It was necessary to remove about a dozen Torx screws to remove the back from the door. The power was turned off at the breaker. Two electrical fittings were removed from the broken handle and placed on the new one, and the part was put into position and the door back screws reinserted. I was fortunate to have the appropriate Torx driver and suggest that PartSelect offer such an unusual tool with the part.

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were replaced and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.

I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.

First I unpluged the wire from the drain pump, Then I removed the drain hose form the drain pump, then removed the screw holding the pump to the bracket. Then just turned the pump to the left and pulled down on the pump. Installed the new pump in the reverse order. Was a very easy install. And the problem is now fixed.

Went to the hardware store and bought a T-20 torx tip and then unscrewed the plastic on the inside of the door, unplugged the dishwasher and replaced the latch assembly. This is an electrical part and it is essential to disconnect the power. I would never buy this dishwasher again. The latch is not something that should break.

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).