ABB1922FEQ11 Amana Refrigerator - Instructions

Pull the refrigerator forward take off the back panel and replace valve seem valve leaking

Followed instructions supplied on Your website. Instuctions were well explained and easy to follow.

Replaced the CNTRL-ELEC board with ease. Just slide back and remove the light cover. Use flat tip screw driver to release and drop down unit. Remove connectors and attach to new board after breaking in half to fit same as old one. Programming is easy, just look at the CODE on the name plate inside the door. Mine is 0-1. Follow procedure of holding the light switch off while touching the freezer control 3 times within 10 seconds. A "P" for programming will appear. Still holding the light switch, touch the refrig control to set for your code. Freezer button says 0, refrig button says 1. When you release the light switch, the programming is done. Mine starts out with a 4-4. It is now working quieter than when it was new and is very cold again.

Found troubleshooting steps for control board (called a jazz board) and ran through the steps. Found the control board (jazz board) was bad. Pull front vent cover where the condenser is off, you will find manufacture manual papers for these steps and for programming of new control board (don't lose these papers for next time). Papers are located under bottom of front right corner of refrig where they are in a bag ( cut bag open and replace back when finished for next time). Replaced board by: 1. Pushing light cover to back to remove 2. Take screwdriver and push on two tabs that hold housing on at each side (will see two holes where they are by looking from behind, with your head inside) push and pull down. There it is 3. Replace board with the tabs that hold it in. (use latex gloves and only touch outside of board, to avoid static electricity to the board. 4. Reinstall and program (Code for your refrig is on cabinet sticker where model and serial no. are) 5. Install a surge protector on the plug for possible surges. Not too bad to install, just finding how it comes out .

Replaced door closer part on hinge. Did not fix problem. Be sure to order mating bushing that goes in the bottom of the door . Part #67004977

unplug refrigerator, take backing off with nut driver. Pull old blade off and put new blade on. Put backing back on and plug in.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Followed the instructions on the website. Removed glass shelf, installed rail and replaced salad crisper bins and glass shelf. Less than 5 minutes!

I tried to do the repair but could not figure out how to take several pieces off ny old crisper frame to put on the new. I ended up recruiting a male friend to help. He's very mechanical and he still had to tinker with it awhile before he figured it out.

Pulled out the broken frame and just put in the new one without having to pressure it in or figure it out. I paid extra for rapid delivery and the next day I had the part arrive.

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

Easy to replace part - remove panel at the bottom rear of the appliance, unplug from the compressor and connect the new relay. Unfortunately, it was not the relay on my appliance -- looks like the compressor has gone out -- new fridge for me

I did it exactly how the video that was shown when I purchased the new rail. Following those instructions worked perfectly.

Viewed the viedo - it showed what to do