Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AAV8000AJW

AAV8000AJW Admiral Washer - Overview

Get Parts and Repair Help for AAV8000AJW

If you know the washer repair part you need, you can browse the list of all parts on the AAV8000AJW, or you can search by name or part description. You can also find your part by where it is located on the AAV8000AJW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AAV8000AJW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$56.03

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - t...

Order within the next 1 hr and 51 mins and your part ships today!
$37.75

Suspension Springs - Kit of 6

Order within the next 1 hr and 51 mins and your part ships today!
$98.98

Hub and Seal Kit

This kit prevents water from leaking around the drive shaft and down to the bottom of the tub.

Order within the next 1 hr and 51 mins and your part ships today!
$67.78

Agitator Auger and Post Assembly

Order within the next 1 hr and 51 mins and your part ships today!
$34.73

Lower Bearing Assembly

Order within the next 1 hr and 51 mins and your part ships today!
$48.23

Agitator Base

Base only. Top agitator sold separately.

Order within the next 1 hr and 51 mins and your part ships today!
$38.58

Lid Switch Kit

This kit includes the bracket, actuator, switch, screws and wire harness.

Order within the next 1 hr and 51 mins and your part ships today!
$13.74

Flume Hose Kit

Order within the next 1 hr and 51 mins and your part ships today!
$381.95

Transmission and Seal Kit

Order within the next 1 hr and 51 mins and your part ships today!

Plastic Outer Tub

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

One of the plastic hinge pins brroke

  • Customer: Allen from North Little Rock, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 478 of 475 people found this instruction helpful
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. read more

bearing on water pump siezed

  • Customer: kevin from rochester, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 105 of 117 people found this instruction helpful
back panel,belt two hoses,three screws, $100 dollars for the part!! pump is a molded part with a bearing insertion, is made in USA ! I'm guessing around 7 to 10 dollar manufacturing cost. I'm thinking that kind of mark-up is only exceded by the pharmacutical industry. I'm looking to buy a used machine for parts!! read more

EXCESSIVE Banging, shaking and squeaking while on Spin Cycle

  • Customer: robert from simpsonville, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 95 of 98 people found this instruction helpful
1)Start with empty washing machine.
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drain into small contain... read more