AAV7000AGW Admiral Washer - Instructions

Took off the lid unscrewed 4 screws and replaced with new parts. Very simple.

Repair went as described in instructions supplied and YouTube Video "snubber ring". I could not have removed tub springs without putting 72 quarters in springs before removing as seen in another repair video which made removal and reinstallation doable. I still don't understand how this inexpensive part can cause such a problem.

To simple the agitator one socket three minutes done. Water leak took longer because we had to move out the washer and took off the back with nut driver and a pair pliers done. Thank you for your incites.

There was a crack in the black rubber hose attached to the water inlet flume assembly, and the assembly itself was cracked and falling apart. 1) Turned off water. 2) Lifted top cover up (pry up with flat screwdriver). 3) Disconnected hose. 4) Trimmed hose above the crack. 5) Replaced "spring" -type hose clamp with small automotive-style clamp. 6) Unbolted flume from under lid (2 sheetmetal screws). 7) Reattached hose to new flume. 8) Reattached flume to underside of lid. 9) Closed lid (light pressure downward required). 10) Turned on water. Total repair time: 10 minutes.

I ordered the new part on a Sunday and it arrived at my house on Tuesday. Removed the back cover plate,(only two screws) removed the two hose clamps and hoses. Removed the three screws holding the old pump to the base and took out the bad pump. Put the new pump in place, (a perfect fit) and put everything back together. Even the belt went back on with ease. The washer was back in place and working perfectly in about 15 minutes.

After reading several online posts about this problem on appliance forums and following the suggestions about how to determine what was needed (whether the inner tub turned freely (by hand) in spin mode or not. It didn't which apparently indicates the likely need for a new thrust bearing. I purchased the transmission pulley and bearing kit from Parts Select. I got it the next day, without asking for next day delivery! When I took the old parts off (easy: pull off the plastic cover, remove the circlip and everything falls off the shaft (if you are working with the washer just tipped up. Unfortunately, that was where my easy repair ended. The parts were entirely different! After looking and looking and thinking, I called Parts Select. They informed me that Whirpool, who makes Maytag had redesigned the parts. They didn't look like they would work, but I followed the directions which came with the kit and installed the new parts - three times. The last time the pulley stayed on and the washer spun as it ought. The problem was that even with the smaller of the spacer washers the circlip was extremely difficult to get in its slot. Anyway, now the washer works and I am pleased, even though I spent many hours on what ought to have taken perhaps 1/2 hour.

Watched video , after that there was no problem, really easy.

Had no problems taking machine apart following online instructions. At first couldn't find snubber ring because it was completely worn away. Once found it was very easy to replace. Only problem with putting back together was getting the first spring back on, after that it was a breeze. Machine up and running.

Washer was jumping around in the spin cycle to the point that it disengaged the water fill level hose which in turn caused it to overflow. I fixed the hose but almost immediateley it stopped spiining or agitating. I looked online to find that the jumping around was most likely the snubber ring ... the hard stop and squeal most likely the Brake Stator ... the no agitaion or spin was likeley the thrust bearing. I ordered the parts and were received in a couple of days ... by the time they came I had already torn apart everything and was just waiting on parts for reassembly. The instructions were concise and complete but I did benefit from watching a YouTube video on the repair. All the parts went together just like they were supposed to even with my limited mechanical skills. All I really used was a small socket set, a couple of screw drivers and a pair of pliers. Taking the Brake assembply is dangerous but can be done with no special tools if you buy a couple of 2 inch 10-24 screws to replace two of the short ones and then back them out slowly (look for a youtube video on this procedure EASY!) ... took me a couple of hours but any one who has used a screw driver more than once could probably do it in under an hour. Washer now running like new ... No Jumping!!! People at Parts Select were Great!!! BTW ... So that the springs would be easier to re-install, I stuck about $50 of quarteres between the coils before removing ... worked Great!

The repair was easy. 5 minutes after grabbing my tools the job was done. It was easy to find the part I needed on the web site.

When I received the replacement part it did not look exactly the same as the one that came off the washer. After watching the video that was sent with the shipment confirmation I very clearly understood it and was able to do repair in about 10 minutes. It was so easy, I wish that there were more repairs to do to take advantage of your wonderful customer service. You have created a customer for life. Thank you

We went on line and found the correct part. It arrived in 3 days. said it might take 7. Husband and son dismantled the old plastic outer tub that had been slit by the screwdriver. Put the new one in, and filled the tub up with water to check for leaks. When the water got to the level of the fill line, it started leaking. We pumped the water out and stopped to wait for daylight. Next day we lifted the top of the machine and filled it again...the line that goes to the water level knob...was off. The woman found the leak and put the hose back on. We were semi worried when we read the reviews, but in the daylight, it really wasn't all that difficult to change out the broken tub.

Took access panel off of back saw that hose had pulled off of tub, thus the rinse water was just running on floor, re attached hose when the rinse cycle finished and the brake stopped the spin it jerked the hose off once again. It had a spring clamp holding it on, so I reinstalled it with a worm/screw clamp, no problems since. Ordered a new hose to have on hand in case. Jim

you need a ratchet with a socket extension 6" or better to remove the bolt then replace the agitator. The Job is extremely easy.

Simply watched your video, which was very well done, followed step by step and in about 20minutes the washer was successfully repaired. You have a great business model, the the part was easy to order, the shipping was prompt and the video was a plus Steven Hopkins