A3637XRA Admiral Range - Instructions

Removed two screws on each end of the bottom element, removed blade wires from element and removed element. Put new element in to place in oven, put blade wires on to end of element and put in the two screws that held the element in place. Watched and followed the video instructions on the website. Very easy to repair.

When we received the new element for the oven. We followed the directions that where given to us and had no problem installing the new element. It took no time before the the oven was working again. thank you for posting the directions to make the job go easier.

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Disassembled upper unit with Phillips screwdriver. Removed 2 "plug connectors" from element switch. Replaced switch. Plugged both connectors back onto switch. Reassembled the upper portion of the range. Tested and OK

KILL POWER FIRST. I should have read other entries on here prior to starting. I would have learned that one leg of the element is always hot. Fortunately it arced against the oven, and all I had to do was replace the terminal. Could have been much worse. Unplug range or shut off circuit breaker prior to doing any electrical work. Verify 0 voltage before starting if you shut off the breaker.

During normal use, the heating element on my electric range burst into flames one day. Judging from the internet, this is actually fairly common! It's an electrical fire, so it's important to shut the oven off at once, and not a bad idea to cut the circuit breaker immediately. Then put the fire out and unplug. Remove what's left of the old element by unscrewing 2 mounting screws where it enters the oven rear wall. Taking door off of oven made it easier to lean in there. Then pull the crimp connections apart to get the wires off of each end. There are videos on youtube and partselect.com showing how. One thing they don't mention is that the wires may want to disappear back into the hole in the oven wall once they're loose. So hang onto them. I put a piece of duct tape around each one to keep it from slipping back into those small holes. When the new element arrived, I just reconnected the two crimp connectors and re-mounted the two screws. Of course, make sure range is unplugged while you're in there. Those two wires have 220V on them. I'm also never again going to leave my range on, either in baking or cleaning mode, when I'm not home. That fire was scary!

just removed two screws installed the unit replaced the two screws

Turned off circuit breaker to oven. Removed old unit by undoing screws and remove from clamp.Put to unit in by placing it to clamps and adjusting so it was level and screwed it back in. Voila! But now I think I need a sensor..

shut power off to range. removed oven shelves to make getting old element out a lot easier. removed screws that hold old element to back of oven - carefully pulled old element out about 3-4 inches. pulled power connectors off end of element. then installed new element in reverse order. Very easy to do. My wife could have done,but she does baking. I do the repairing. Thank-you for such great service. Greentown joe

turned breakers off unscrewed two screws, removed old element.Reattached wires on new element,put two screws back in. flipped breakers back on and its good to go.

number 1 was to shut off circuit breaker. Just removed 2 screws pulled out element slowly to expose wire terminals, removed wires carefully so terminal was not damaged. Replace element was spot on so install was in less than 5 min.

killed power...removed back of stove...removed switch and replaced it..reinstalled back...powered up

Turn the power off at the breaker first! then I used a phillip head screwdriver and unscrewed the two screws that was holding the metal plates on, then pulled the element out with the wires connected and pulled off the terminals. Then i put the new element in and hooked the wires to the terminals then pushed back through the back of the oven then screwed the plates back on then it was done!

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

The video was good but my model had and additional back plate that wasn't mentioned with 6 additional screws to take out and put back in. Other than that the video explained everything including checking the wires, clips. Oven works great now.