A3531WRW Admiral Range - Instructions

plugged it in to the spot where missing element was.

Our Maytag Gemini is about 10 years old. One night the 8" front right element was smoking and had a white hot spot on the burner. I quickly turned it off and after the element cooled I removed it. Since one 8" element was burned out, but the rest of the range and oven worked, I assumed I could get it fixed. Rather than call the service man for $99 for a diagnostic visit, I decided to go to PartSelect and get prices on parts. They had the easiest site to use with part numbers, exploded part drawings, etc. Since I had to replace one burned out element anyway, I ordered the burner and the wiring receptacle. I assumed that was step one. The parts came in about two days. It took me about 20 minutes to put them in with no problems. Very easy. However, the burmer still would not work. I went back to the site and determined the only other part it could be was the infinite switch. The bad element little light on the top control panel was not going out even after I put in new parts. I figured it was shorted out and frozen in the closed position, so I ordered a new one from PrtSelect. It came again in about two days. This part was easy to replace, except it took longer because the entire back of the oven had to be removed. Three pieces of sheet metal had to be removed and two plastic end caps. Sheet metal has sharp edges. Watch out that you do not get cut. A lot of screws got removed and put back. You have to be careful that the three pieces of sheet metal are put back correctly because several edge tabs lap over each other. The infinite switch fixed the problem. Took me about two hours to do the switch replacement, but that counted cleaning the sides of the oven and underneath the oven (Yuch!). Now everything works fine. I suspect that the old wiring receptacle was fine and just the infinite switch and element needed to be replaced. In any case, the wiring receptacle was cheap. In the end, the repair cost me the same $99, but I spent it in parts and not parts plus installation so I was way ahead.

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

KILL POWER FIRST. I should have read other entries on here prior to starting. I would have learned that one leg of the element is always hot. Fortunately it arced against the oven, and all I had to do was replace the terminal. Could have been much worse. Unplug range or shut off circuit breaker prior to doing any electrical work. Verify 0 voltage before starting if you shut off the breaker.

During normal use, the heating element on my electric range burst into flames one day. Judging from the internet, this is actually fairly common! It's an electrical fire, so it's important to shut the oven off at once, and not a bad idea to cut the circuit breaker immediately. Then put the fire out and unplug. Remove what's left of the old element by unscrewing 2 mounting screws where it enters the oven rear wall. Taking door off of oven made it easier to lean in there. Then pull the crimp connections apart to get the wires off of each end. There are videos on youtube and partselect.com showing how. One thing they don't mention is that the wires may want to disappear back into the hole in the oven wall once they're loose. So hang onto them. I put a piece of duct tape around each one to keep it from slipping back into those small holes. When the new element arrived, I just reconnected the two crimp connectors and re-mounted the two screws. Of course, make sure range is unplugged while you're in there. Those two wires have 220V on them. I'm also never again going to leave my range on, either in baking or cleaning mode, when I'm not home. That fire was scary!

just removed two screws installed the unit replaced the two screws

Turned off circuit breaker to oven. Removed old unit by undoing screws and remove from clamp.Put to unit in by placing it to clamps and adjusting so it was level and screwed it back in. Voila! But now I think I need a sensor..

So purchased two new 8 inch elements and replaced them.

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

followed your excellent video and the job was a breeze Thank you !

Oven is built in. The only way to access the hinges is to pull the oven out and remove the sides.

shut power off to range. removed oven shelves to make getting old element out a lot easier. removed screws that hold old element to back of oven - carefully pulled old element out about 3-4 inches. pulled power connectors off end of element. then installed new element in reverse order. Very easy to do. My wife could have done,but she does baking. I do the repairing. Thank-you for such great service. Greentown joe

turned breakers off unscrewed two screws, removed old element.Reattached wires on new element,put two screws back in. flipped breakers back on and its good to go.

number 1 was to shut off circuit breaker. Just removed 2 screws pulled out element slowly to expose wire terminals, removed wires carefully so terminal was not damaged. Replace element was spot on so install was in less than 5 min.

I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.